0
What else can I help you with?
Is there any difference in temperature at inlet and outlet of steam turbine?
For efficiency's sake, the outlet had best be a lot cooler.
What has the author William J Kearton written?
William J. Kearton is a well-known author and naturalist who, along with his brother Richard, wrote several books on wildlife and nature photography in the late 19th and early 20th centuries. They are best known for their pioneering work in nature photography and their book "Nature Near London" which showcased their early efforts.
Best type of power plant?
Nuclear power is the best by far because you take pellets that have a uranium orb in the middle then stabilizer rods come in stabilize them and then water is poured on them to generate steam that rises through a turbine and spins the turbine generating power
How many kg of steam required to produce 1 KWh for steam turbine of 30bar pressure and 390oC temp?
I'm currently benchmarking a number of plants in my company which produce steam for downstream processing. What is a typical kWh/kg of steam ratio I could set as a best practice target? Thanks Paul
What is troubleshooting procedure for temperature sensor on a Mr steam Commercial Generator?
The manufacturer is the best source of that information
What are the best features of the concrete steam cleaner for effective cleaning?
The best features of a concrete steam cleaner for effective cleaning include high temperature steam for deep cleaning, adjustable pressure settings for different surfaces, and attachments for reaching tight spaces.
Application of tesla turbine to electrical field?
This Tesla CD Turbine is based on the Tesla turbine, which was invented by Nikola Tesla in the early 1900's. Tesla's pumps and motors were unique in that they only used discs, and took advantage of the boundary layer effect. His smallest designs were over 100 horsepower. It is referred to as a bladeless turbine because it uses the boundary layer effect and not a fluid impinging upon the blades as in a conventional turbine. The Tesla turbine is also known as the boundary layer turbine, cohesion-type turbine, and Prandtl layer turbine (after Ludwig Prandtl). One of Tesla's desire for implementation of this turbine was for geothermal power, which was described in "Our Future Motive Power". Tesla wrote 'This turbine is an efficient self-starting prime mover which may be operated as a steam or mixed fluid turbine at will, without changes in construction and is on this account very convenient. Minor departures from the turbine, as may be dictated by the circumstances in each case, will obviously suggest themselves but if it is carried out on these general lines it will be found highly profitable to the owners of the steam plant while permitting the use of their old installation. However, the best economic results in the development of power from steam by the Tesla turbine will be obtained in plants especially adapted for the purpose.
What best describes the operation of a waste gate turbo charger?
The waste gate controls the boost coming out of a turbo by bleeding off exhaust gases/pressure to the turbo's turbine. By control the amount of gases/pressure the turbine see's, it controls the turbo's speed/pressure.
Which is best for any industry pelton wheel or francis turbine?
francis turbine
What points in the energy flow through power plant that might produce unwanted forms of energy and make the plant less efficient?
Let's consider a coal-fired power plant. Here we have a boiler that burns coal to produce steam. The boiler radiates heat and this radiant heat loss causes an efficiency penalty - about 1% of the energy in the coal is lost in radiation. Moisture that was in the coal to start with (and even moisture in the air because of humidity) gets heated up in the boiler but does not contribute to the process of combustion. This also causes and efficiency loss. Instead of being properly burned up un the furnace, some of the coal particles just fall to the bottom of the furnace, and is collected along with the ash. The steam that the boiler produced goes to a turbine that spins like a fan because of the pressure in the steam. The turbine drives a generator that produces the electricty that comes out of the power plant. Both the turbine and boiler have some losses due to friction, but the main loss in the turbine is the energy in the steam leaving the exhaust of the turbine. Because we want to condense this steam back into water so we can re-use it for supplying the boiler, the energy lost from the exhaust of the turbine actually makes its way to the cooling tower before being rejected into the atmosphere. It seems inefficienct to do it this way, but it's the best method we have at the moment.
What should eccentricity be on a steam turbine before startup?
eccentricity measurementof shaft at slow roll speed. WITH BEST RGARD AZIZ JAMALI SR SUPERVISOR INSTRUMENT FFBL KARACHI PAK AZIZ.JAMALI@YAHOO.COM +923462243209
What are some of the best rated cleaning mops?
Some of the best rated cleaning mops are the Eureka Enviro Steamer, the H2O Steam Mop and the Bissell Steam Mop. Rounding out the top 5 Best Rated Steam Cleaning Mops are the Steam Boy Steam Mop and the Lysol Steam Mop.
