0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is a sprinkler system for a house?
A sprinkler system is a device that waters your plants or grass
What is a sprinkler?
An irrigation sprinkler is a device that applies water to plants, mimicking the effect of rain, as it is done in lawn, garden and agricultural irrigation. A fire sprinkler is a device that discharges water when the effects of a fire have been detected, such as when a predetermined temperature has been reached.
What is wrong with your sprinkler system if water shoots out of your backflow relief valve when you first turn on the sprinkler water source at the beginning of the sprinkler season?
The unit must be installed 12 inches (300 mm) above ground and no more than 30", check with local authorities. The RP assemblies may spit out water of relief port for a variety of reasons so they must have a floor drain if being installed inside a building. Some of the reasons for spitting or flow from relief valve ports are if they detect backflow, inlet/outlet pressure fluctuations, dirt, or debris on first check valve or relief valve. Check trouble-shooting guides. It is also recommended that a strainer be installed with a RP device due to the sensitivity of the check valves and relief valve ports to dirt or debris
Where is theTamper in Sprinkler system?
The Tamper switches for a fire sprinkler system are located on the main control valves which are located on either side of the backflow preventer for a wet type automatic fire sprinkler system. These switches are wired into the monitoring control system/alarm panel to ensure the valves remain open at all times (or not tampered with.) If the tamper switches are used they will show a supervisory trouble on the panel so the monitoring company or business will know there system is out of service.
What is the only way to prevent back flow?
In plumbing, by using a device known as a backflow preventer. It only permits water to move in one direction.
How do you install a sprinkler system?
There are two main methods of sprinkler system installation: open trench and pulled pipe. Open trench typically uses PVC pipe and pulled pipe typically uses poly pipe. Other than the pipe and fittings, the main difference in installation will be that the pulled pipe system requires a hole and saddle tee at the location of each sprinkler head. The steps for installing an automatic sprinkler system using an open trench method are: 1. Start with a good sprinkler system design (try searching "sprinkler system designer" for support options) 2. Make sure that you have all necessary tools, equipment, and permits 3. Have Blue Stakes mark all utilities prior to any digging 4. Install a backflow prevention device according to code 5. Place flags at the location of each sprinkler head 6. Mark and dig all trenches and valve manifold locations 7. Build and install valve manifolds (preassembled valve manifolds can make this easier) 8. Connect mainline pipe from water source connection to valve manifolds 9. Lay lateral line pipe from the valve manifolds to the location of each sprinkler head 10. Install tees and swing assemblies for each sprinkler head and flush lines 11. Connect sprinkler heads to swing assemblies; set head to level with ground 12. Install sprinkler timer/controller and connect sprinkler wire from timer to valve manifolds 13. Install nozzles on sprinkler heads 14. Install valve boxes (as required) and backfill all trenches 15. Run a zone by zone test and adjust nozzle patterns
Which type of device causes the purposeful dissemination of radioactive?
radiation dispersal device
What is a check valve?
This is a device which prevents the reverse flow of air, water (which ever type of system it is installed on). A check valve is an anti-backflow device that keeps a gas or fluid from flowing backwards in a designed system if the pressure falls or goes negative. In your home for instance
What is a landscape backflow prevention device?
It is a form of check valve in a pipe or hose bib that allows water to only move in one direction. This is required by code to prevent a loss of system pressure from creating a vacuum in a line that can suck landscape water back into the system and contaminate the potable water supply. A Vacuum breaker for a lawn sprinkler must be located at lease 12" above the highest head. A hose Bib vacuum breaker is not code approved in modern codes
Typically sprinkler heads contain a or that acts as a stopper to the water behind it. A. Rubber plug metal link B. Special computer chip wired signaling device?
a.
What is actuater?
An actuator is a device which actuates something else - especially a mechanism which causes a device to be switched on or off.
How do you stop a continuous loud humming sound that stops when you turn on a faucet but then begins again?
it's probably the check valve(backflow prevention device)at the water meter. call your water company and ask them to replace it.
