0
condensate,bleed line of all condensate
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Why do you need a steam bypass control valve?
to let the steam pass and avoid an explosion under some undesireable circumstances.
What is the porpuse of steam?
the purpose of steam is to make the meat or other food get soft and make heat. to avoid uncooked food.
Why is it necessary to open casing drains and drains on the steam line going to the turbine when a turbine is to be started?
To avoid slugging nozzles and blades inside the turbine with condensate on start-up; this can break these components from impact. The blades were designed to handle steam, not water.
What is the difference between saturated steam and Superheated steam?
Saturated steam occurs when steam and water are in equilibrium. If you have a closed container of water and heat it, above 100 celsius the steam pressure will start to rise, and as the temperature continues to rise, the pressure will go on rising. What is happening is that steam is being evolved to match the temperature (steam tables will give this relation) and the steam conditions are said to be saturated because if the pressure is raised by external means, some of the steam will start to condense back to water.If the steam pressure is held at a lower level than that achieved at saturation, by taking steam off to feed a turbine or other steam usage, there is effectively an excess temperature for that pressure, and the steam is said to be superheated. It in fact then becomes dry, and behaves as a gas. The amount of superheat can be quantified as so many degrees of superheat (celsius or fahrenheit).Turbine designers want steam to be superheated before reaching the turbine, to avoid condensation causing blade erosion, and steam producing boilers in power plants are designed to produce superheated steam. In plants where no turbines are used, only satured steam is normally generated.In heating applications, saturated steam is preferable, because it has a better energy exchange capacity. Superheated steam must cool down, and become saturated steam, before condensing in a heat exchanger. Also, superheated steam is a thermal insulator, like air.That is why it is necessary to direct superheated steam through a desuperheater before using the steam in heating applications.
What do you understand by property of a system?
The property of steam is the precipitants ingress through the water in to the steam cycle The steam conductivity and silica contents so called property of steam. there fore the boiler drum chlorides(cause of higher conductivity in the Super heated steam) and water PH has to be controlled to get pure Super heated Steam from boiler drum risers. Silica can cause of turbine blades erosion. Higher Conductivity cause of Chlorides which can cause of Corrosion on turbine blades. PH controlled to avoid acid attack and pitting and scales deposition.
Why hammering is happening in steam line?
condensate in the steam piping, probably due to improper slope of piping to allow condensate flow out.
How hot does the steam get on a steam engine?
The temperature of the steam in a steam engine will vary as the pressure of the steam. The higher the pressure, the higher the temperature that the steam headers (pipes) will run at. Because pressure varies between steam engines, temperature will vary also. Those temperatures could be from between 300 to 400 degrees on up to 700 to 800 degrees Fahrenheit, depending on the actual pressure the boiler is running at.Toy - Model steam engines typically use much lower steam pressures, and these machines run at 220F to about 250F
What do you do when you are in the ship when the pipes are blowing steam on SOS island?
avoid the pipes that shoot steam it will happen in the third and fifth rescue.
Why do you need a steam bypass control valve?
to let the steam pass and avoid an explosion under some undesireable circumstances.
What is the porpuse of steam?
the purpose of steam is to make the meat or other food get soft and make heat. to avoid uncooked food.
When was The Hammering Process created?
The Hammering Process was created on 2000-10-26.
What is borla headers?
Borla headers are by far the best aftermarket headers available for performance cars and trucks.
What is AH mode?
authentication headers authentication headers
Hammering hot iron into a sheet chemical or physical change?
Physical one.
Did a 440 big block in a 69 dodge charger have exhaust headers?
all engines have exhaust headers but the headers your thinking of are aftermarket performance headers, the ones on the 440 from the factory are made of cast iron.
How much does a cars headers weight?
Proper headers will weigh between 12 pounds to 35 pounds for a small set of V8 headers
What is better long tube headers or short tube headers?
what kind of headers do i use when installling a 72 olds 350 rocket into a 85 olds cutlas supreme ? long tube or short tube headers
