Watts from a socket is dependant upon what the load connected draws. The maximum capacity from a socket is calculated by the following equation, W = A x V. So the maximum wattage you are able to draw from the socket before the fuse blows is W = 13 x 220 = 2860.
120 volts is a standard voltage in US for normal house hold electric outlet. , So you can buy from 0 watts to 1000 watts for 120Volts socket . However the bulb you want to buy depend on the Lamp holder , rating of the socket and where the holder is installed, how much light you need etc . Check the max Watts rating on your socket or Lamp and determine the correct Wattage bulb to use. No one can tell you what wattage bulb to use with out looking at your socket or Lamp. The formula for Watts = Volts x Amps Check out the low wattage Compact Fluorescent Light Bulbs which will consume very low engergy and save money in a long run http://www.energystar.gov/index.cfm?c=cfls.pr_cfls
Two thoughts here, one the fixture should be rated at the maximum wattage allowed for the socket the bulb screws into. A label should state "maximum wattage allowed". To do a calculation Watts = Amps x Volts. Amps = Watts/Volts. 5 x 60 watts = 300 watts. 300/120 = 2.5 amps. The electrical code only rates down to #14 wire which is rated at 15 amps. From here you have to make the decision.
Electric lamps have a wattage rating, but also have voltage ratings. Additionally, there are different socket styles for lamps, too.
Obviously not. It would blow the bulb by 600W! <<>> Yes you can use a 60 watt light bulb in a lampholder that is rated a 660 watts. The rating given to these lamp holders is the maximum amount of wattage that can be applied to them safely.
You can use a three way bulb in a one way socket. I believe the default wattage will be the middle one. E.g., a 30-70-100 watt three way will default to 70 watts in a one way lamp or socket.
Find the wattage rating on the dimmer controller. This is the maximum allowable wattage that the lamp in the fixture should be. Lamp wattage ratings under the rated dimmer wattage is fine but do not install a larger wattage lamp that is over the dimmer control's rating.
Watts from a socket is dependant upon what the load connected draws. The maximum capacity from a socket is calculated by the following equation, W = A x V. So the maximum wattage you are able to draw from the socket before the fuse blows is W = 13 x 220 = 2860.
Yes and no. There is a small range of wattage for which the built in ballast is designed for. Best to stick with the original wattage 4 pin lamp.
300watts
120 volts is a standard voltage in US for normal house hold electric outlet. , So you can buy from 0 watts to 1000 watts for 120Volts socket . However the bulb you want to buy depend on the Lamp holder , rating of the socket and where the holder is installed, how much light you need etc . Check the max Watts rating on your socket or Lamp and determine the correct Wattage bulb to use. No one can tell you what wattage bulb to use with out looking at your socket or Lamp. The formula for Watts = Volts x Amps Check out the low wattage Compact Fluorescent Light Bulbs which will consume very low engergy and save money in a long run http://www.energystar.gov/index.cfm?c=cfls.pr_cfls
10
In the US at least, no, linear amps are not legal for use on CB radios. The maximum wattage permitted for AM transmission is four watts, and the maximum wattage permitted for Single Sideband is 12 watts.
300 W.
Two thoughts here, one the fixture should be rated at the maximum wattage allowed for the socket the bulb screws into. A label should state "maximum wattage allowed". To do a calculation Watts = Amps x Volts. Amps = Watts/Volts. 5 x 60 watts = 300 watts. 300/120 = 2.5 amps. The electrical code only rates down to #14 wire which is rated at 15 amps. From here you have to make the decision.
You can use a lower wattage bulb on a higher wattage fixture provided the voltage rating is the same and the bulb base is the same.
Wattage.