0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What do you mean by strobe gate?
strobe is enable input in a digital IC...if its made active high...it will be enabled..some IC strobe is active low.. Its function is to enable the operation of the IC..or gate or Mux...
Why transistor is called transfer of resistor?
Transistor=Transfer+Resistor. When Transistor operates in active region its input resistance is high and output resistance is low. So,We can consider transistor as a device which transfers its resistance from high to low. And by this property transistor amplifies input signal.
Why most IC are active low?
Most control signals in electronics are active-low signals (usually reset lines, chip select lines and so on). This stems from the fact that most logic families can sink more current than they can source, so fanout and noise immunity increase. (The reason for this is ultimately related to the fact that electrons are negatively charged.) It also allows for wired-OR logic if the logic gates are open-collector/open-drain with a pull-up resistor. Examples of this are the I²C bus and Controller Area Network (CAN).
Does a Digital Voltmeter have a high or low input impedance?
Digital voltmeter has high input impedence.
What gate the output will be low for any case when one or more input are zero?
An inverter has a high output when the input is low, and a low output when the input is high.
What is meant by the terms 'active high input' and 'active low input'?
The term "active low" means that the input on an IC requires a logic low for it to be activated, i.e a low voltage (of course the voltage range is dependent on the technology, TTL, CMOS etc) Active high is the opposite... the input requires a logic high for it to be activated. A simple example to illustrate, an 8bit counter can count UP/DOWN this functionality is controlled with only one pin, an active high on that pin to count up or low to count down.
What are the main differences between FETs and BJTs in terms of input impedance?
FET has very high input impedanceBJT has very low input impedance
What is meant by amplifier?
An amplifier amplifies the small input signal to a high signal without changing its freqency.
What do you mean by strobe gate?
strobe is enable input in a digital IC...if its made active high...it will be enabled..some IC strobe is active low.. Its function is to enable the operation of the IC..or gate or Mux...
Why transistor is called transfer of resistor?
Transistor=Transfer+Resistor. When Transistor operates in active region its input resistance is high and output resistance is low. So,We can consider transistor as a device which transfers its resistance from high to low. And by this property transistor amplifies input signal.
Do you need the high input piece for the amp to get it to work?
high input is for speaker level input and low input is rca jacks
Why most IC are active low?
Most control signals in electronics are active-low signals (usually reset lines, chip select lines and so on). This stems from the fact that most logic families can sink more current than they can source, so fanout and noise immunity increase. (The reason for this is ultimately related to the fact that electrons are negatively charged.) It also allows for wired-OR logic if the logic gates are open-collector/open-drain with a pull-up resistor. Examples of this are the I²C bus and Controller Area Network (CAN).
Does a Digital Voltmeter have a high or low input impedance?
Digital voltmeter has high input impedence.
Why is JFET used as an input device?
it has high input impedance
Why the input resistance of opamp is high?
Because op amp consist differential amplifier and they posses high input impedance so that op-amp also posses high input impedance.
What gate the output will be low for any case when one or more input are zero?
An inverter has a high output when the input is low, and a low output when the input is high.
What is meant by active optics?
Active optics are where you manipulate the mirrors and lenses in your telescope to compensate for the swimming effects in your images caused by the motions of the gases in the atmosphere. These techniques have become possible with the advent of cheap high speed computers.
