0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are the main features of instrumentation amplifier in instrumentation system?
High Common Mode Rejection Ratio is the main feature of instrumentation amplifier! And other features are high input impedance, low output impedance, high slew rate, low power consumption, more accurate, easier gain adjustment, low thermal and time drift.
What are the advantages of instrumentation amplifier over differential amplifier?
a differential amplifier helps to increase the CMRR which in turn helps avoid unwanted signals that couple into the input to get propagated. IT also helps to increase the signal to noise ratio. furthermore it provides larger output voltage swings.
What is invertion?
An inverting amplifier is one where the output is an inverted function of the input. The Class A transistor amplifier, also known as common-emitter, is inverting. As you increase the voltage on the base, the output voltage on the collector decreases. The operational amplifier has an inverting and a non-inverting input. In typical bridge mode, the output is inverted with respect to the (inverting) input, and the non-inverting input is used to reject common-mode input signals by moving the virtual ground point as needed.
What are the characteristics of instrumentation amplifier?
a high common mode rejection ratio, high impedance
What is a difference between an operational amplifier and instrumentation amplifier and can you use one opamp to perform a same task as 3 opamp instrumentation amplifier?
An op amp is made from transistors, resistors and capacitors. It is enclosed in a "chip". A basic instrumentation amp is made of 2 op-amps. you can't have a single op-amp perform as good as a instrumentation amp, although it can perfrom the same task. An i-amp has much better CMMR (common-mode rejection) and a higher input impedance.
Why does your amplifier keep going into protection mode?
A shorted output, bad output transistor. need more info.
What is Linear system in electronics?
A linear electronic device is one where output is linearly proportional, in some way, to input. An example is an amplifier. A non-linear device is one where the input drives the circuit into some kind of saturation mode. An example is a switch, such as is used in TTL IC's.
What are the characteristics of a CB amplifier?
it is a mode of amplifier connection where the base part of the transistor is made common to both input and output.the circuit diagram is as shown below. the transiator gain(represented by the greek letter beta-B) is usually evaluated by the formula B=output current divided by input current. as we know that when the transistor is connected in common base mode the input pert will be emitter and the output part will be collector and we know that the collector current is quiet less than emitter current. as per the formula gain will be less than one. practically we consider emitter current as equal to collector current and hence B approaches 1 in case of common base mode amplifiers.as the gain is very less it is very less used as amplifiers. generally they use common emitter mode for amplification as this mode optimum amount of amplification.
What Input 11234 Output Mean 2.2 Mode 1 Min 1 Max 4?
Input: 1, 1, 2, 3, 4 Output: Mean: (1+1+2+3+4)/5 Mode: 1 the value that occurs most frequently in the input Min: 1 is the minimum value of the input Max: 4 is the maximum value of the input
Can you hook two amps together and get one combined power?
If you mean in series (the output of amplifier a plugs into the input of amplifier b), probably not. Unless amp b can handle the input power delivered by amp a, and then linearly amplify that signal up to its own level, you will get massive distortion. If you've ever heard an electric guitar in maximum overdrive mode, you have a sense of what will happen. The way to do this is give each amp 1 speaker and y-cord the INPUT of each amp.
What is opamp?
An operational amplifier, which is often called an op-amp, is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output.[1] An op-amp produces an output voltage that is typically millions of times larger than the voltage difference between its input terminals.Typically the op-amp's very large gain is controlled by negative feedback, which largely determines the magnitude of its output ("closed-loop") voltage gain in amplifier applications, or the transfer function required (in analog computers). Without negative feedback, and perhaps with positive feedback for regeneration, an op-amp essentially acts as a comparator. High input impedance at the input terminals (ideally infinite) and low output impedance at the output terminal(s) (ideally zero) are important typical characteristics.Op-amps are among the most widely used electronic devices today, being used in a vast array of consumer, industrial, and scientific devices. Many standard IC op-amps cost only a few cents in moderate production volume; however some integrated or hybrid operational amplifiers with special performance specifications may cost over $100 US in small quantities. Op-amps sometimes come in the form of macroscopic components, (see photo) or as integrated circuit cells; patterns that can be reprinted several times on one chip as part of a more complex device.The op-amp is one type of differential amplifier. Other types of differential amplifier include the fully differential amplifier (similar to the op-amp, but with two outputs), the instrumentation amplifier (usually built from three op-amps), the isolation amplifier (similar to the instrumentation amplifier, but which works fine with common-mode voltages that would destroy an ordinary op-amp), and negative feedback amplifier (usually built from one or more op-amps and a resistive feedback network).
What is common mode output voltage?
I assume you're referring to an amplifier circuit. In a differential amplifier, there are two inputs. The common mode output voltage is the output voltage that will result from the same voltage being applied to both inputs. Typically this is very low, as the common mode rejection ratio (CMRR) is very high in a differential amplifier. This is an ideal characteristic (high CMRR) as it means unwanted noise will not be amplified and potentially squelch out the desired signal; this is why a differential amplifier is used in high quality sound equipment. Three wires are used - a ground, and two signal wires that are opposite each other. Noise will inherently "hop on" the signal wires, but as they are close to one another, it is likely the noise will be nearly the same magnitude and sign on each wire. Since the amplifier CMRR is high, this noise does not propogate through the amplifier, while the original signal is amplified.
