there should be 5 wires, hot and switched hot for the switch and hot, neutral and ground for the gfci receptacle.
A GFCI is not an overcurrent protection device. It only protects people from electrical shock. However, if you were to create a perfect hot to neutral short the GFCI would not trip and the panel breaker would.
Open in this context means that the power is not connected and hot means it is.
It is normal for GFCI breakers and receptacles to feel warm to the touch while under load. They should not feel "hot". GFCI receptacles often protect other receptacles further down the line, so the load does not necessarily need to be plugged into the GFCI receptacle itself. AFCI breakers will also feel warm to the touch. Again the receptacles should not feel "hot". If they are hot or heat discolored, you should discontinue use and call a licensed electrician. C. P., Master Electrician
Find the Hot side of the switch (Where there is voltage regardless of position of toggle on switch). Tie in new Black wire to GFCI. On wire nut with white wire tie in new white wire to GFCI. Do the same for the bare ground wire, if there is one.
A GFCI monitors the current in the ungrounded (hot) conductor and the grounded (neutral) conductor. If there is more than 6mA of current difference between the two the GFCI will open the circuit.
there should be 5 wires, hot and switched hot for the switch and hot, neutral and ground for the gfci receptacle.
A GFCI is not an overcurrent protection device. It only protects people from electrical shock. However, if you were to create a perfect hot to neutral short the GFCI would not trip and the panel breaker would.
Open in this context means that the power is not connected and hot means it is.
Yes it should .
It is normal for GFCI breakers and receptacles to feel warm to the touch while under load. They should not feel "hot". GFCI receptacles often protect other receptacles further down the line, so the load does not necessarily need to be plugged into the GFCI receptacle itself. AFCI breakers will also feel warm to the touch. Again the receptacles should not feel "hot". If they are hot or heat discolored, you should discontinue use and call a licensed electrician. C. P., Master Electrician
GFCI's monitor current in the hot and neutral wires to make sure they match. If they don't, it's considered a ground fault, and the GFCI trips. However: If you're taking this test, you're being tested on your electrical knowledge, the strength of which may cost someone their life one day. It's not about homework or test questions, but you're asking a homework or test question in a trade dangerous enough for people to need licenses. ----If you do not understand the work well enough to accomplish it yourself properly and safely, don't try it. Consult a professional electrician, as they are proficient enough to do it properly and safely. When working on electrical circuits and equipment, make sure to de-energize the circuit you will be working on. Then test the circuit with a definitive means to make sure it is off (multimeter with metal tipped leads, voltage tester with metal tipped leads, etc., not a non-contact tester, which is non-definitive.)
Yes provided you have a ground, neutral and hot wire coming to the box.
Find the Hot side of the switch (Where there is voltage regardless of position of toggle on switch). Tie in new Black wire to GFCI. On wire nut with white wire tie in new white wire to GFCI. Do the same for the bare ground wire, if there is one.
No. A GFCI receptacle does NOT require a ground wire to operate properly or to meet code. The GFCI device measures current in the hot and neutral wires and makes sure they match. The device trips when the currents do not match, indicating that the current is not following the proper path (ground fault). Actually, replacing an old 2 wire ungrounded receptacle with a GFCI is a code approved way to upgrade to 3 wire grounded receptacles. The GFCI and any outlet(s) protected by it are allowed to be 3 wire receptacles. ----If you do not understand the work well enough to accomplish it yourself properly and safely, don't try it. Consult a professional electrician, as they are proficient enough to do it properly and safely. When working on electrical circuits and equipment, make sure to de-energize the circuit you will be working on. Then test the circuit with a definitive means to make sure it is off (multimeter with metal tipped leads, voltage tester with metal tipped leads, etc., not a non-contact tester, which is non-definitive.)
There are two sets of terminals on a GFCI. They are labeled LINE and LOAD. Each set has a hot and a neutral. To wire a GFCI to an older two wire system without a grounding conductor, you terminate the hot wire coming from the panel to the line terminal(usually the brass colored one) and the neutral wire to the other one(usually the silver colored one). If there is another set, or sets(black and white) in the outlet box, they terminate on the load terminals respectively. Code requires any GFCI that has no grounding conductor(the bare one in modern wiring), to have the sticker which states no grounding conductor. This sticker comes with a new GFCI. The GFCI will still operate when there is a ground present. Basically, a GFCI monitors the current between the hot and neutral, if there is any imbalance, which would happen if some of the current was going through another grounded means, it will trip, thereby protecting you .
It meens it is thirsty or it is hot