0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How is pressure treated lumber different from regular lumber?
Pressure treated timber is timber impregnated with chromated copper arsenate under pressure and vacuum cycles. These preserve the timber from various fungicides that would normally eat the timber reducing its life-span.
How do you tanalise timber?
Timber is 'TANALISED' (treated) in an industrial treatment vessel using TANALITH preservative applied using vacuum pressure technology. TANALITH and TANALISED are registered trade marks of the preservative manufacturer, Arch Timber Protection, and may only be used to describe industrial timber treatment using TANALITH preservative. The treatment process consists of 5 stages: 1. Timber is loaded into the treatment vessel. An initial vacuum is applied, and the timber cells are evacuated of air. This vacuum is held. 2. The cylinder is flooded under vacuum with TANALITH wood preservative. 3. Hydraulic pressure is applied, forcing the preservative deep into the structure of the timber. 4. A final vacuum extracts excess preservative solution, which is then pumped back into storage. 5. Low pressure inside timber draws in surface solution when vented to atmosphere. The treated timber is then left to dry - a minimum holding time of 48 hours is recommended. In Europe, TANALITH E preservative is used, which contains copper and triazole biocides, which are commonly used to protect food crops. TANALISED E pressure treated timber can be used in a range of applications, from construction timbers through to heavy duty, highway fencing applications, where a desired service life of 15 years plus can reasonably be expected. Note that where TANALISED treated timber is cross cut, notched or bored following treatment, liberal coating of ENSELE end grain preservative is required to maintain the integrity of the preservative system. Further information on TANALITH E and the treatment process can be found on the Arch Timber Protection website at www.archtp.com. General information regarding timber treatments is available on the Wikipedia site: http://en.wikipedia.org/wiki/wood_preservation
When placed in the ground will a pressure treated 2X4 last as long as a pressure treated 4X4?
If the pressure treatment is identical, theoretically they should perform equally.
How long does pressure treated wood last when treated?
Pressure treated wood can last up to 20 years or more and most pressured treated wood sold in stores such as Home Depot offer a limited lifetime warranty.
Can pressure treated lumber be set in concrete?
yes it can
How is pressure treated lumber different from regular lumber?
Pressure treated timber is timber impregnated with chromated copper arsenate under pressure and vacuum cycles. These preserve the timber from various fungicides that would normally eat the timber reducing its life-span.
Can tanalised wood be painted?
TANALISED timber relates to timber that has been industrially treated with TANALITH preservative under vacuum in an enclosed treatment vessel. The preservative manufacturer, Arch Timber Protection, has a website at www.archtp.com with a Consumer Information Sheet which contains advice regarding compatible glues for TANALISED E pressure treated timber. A range of glues are advised, depending on the end use of the treated timber.
Can you get arsenic poisoning from handling Tanalised wood?
Tanalised timber refers to wood that has been industrially treated using a controlled vacuum pressure process with the Tanalith preservative.Tanalith C preservative contains chromated copper arsenate. In Europe, the use of Tanalised C pressure treated timber was restricted in 2006, and its successor in this market is Tanalised E pressure treated timber, which contains copper and triazole biocides.Timber treated with any Tanalith preservative is resistant to leaching but should be handled with care and any exposed skin is recommended to be washed before eating, drinking or going to the toilet. Avoid handling treated timber that is wet.See the Related links for more information.
When was Treated Timber Resists Rot created?
Treated Timber Resists Rot was created in 2008.
What Is c16 timber?
C16 timber is sawn softwood structural timber which has been treated and strength graded
Is tanalising an oil based or water based wood treatment?
TANALISED pressure treated timber has been impregnated with TANALITH E, a waterborne product.
Can you burn tanalised wood in your fire?
When a component treated with TANALITH wood preservative, applied using a vacuum pressure treatment process, reaches the end of its useful service life, there are a number of methods to consider for its disposal. These options are dependent on the formulation of TANALITH preservative that the timber was treated with. Visit the Arch Timber Protection website at www.archtp.com for further information on this subject. When a component treated with TANALITH wood preservative reaches the end of its useful service life, there are a number of methods to consider for its disposal. These options are dependent on the formulation of TANALITH preservative that the timber was treated with. Visit the Arch Timber Protection website at www.archtp.com for further information on this subject.
What will happen to your health if you burn tanalised timber in an open fire?
Tanalised timber refers to wood that has been industrially treated using a controlled vacuum pressure process with Tanalith preservative. Tanalised and Tanalith are registered trade marks of Arch Timber Protection, and may not be used to describe other formulations.Tanalith C preservative contains chromated copper arsenate (CCA). In Europe, the use of Tanalised C pressure treated timber was restricted in 2006, and its replacement there is Tanalised E pressure treated timber, which contains copper and triazole biocides - which are commonly used to protect food crops.The options for disposal of Tanalised wood are dependent on the formulation of Tanalith preservative that the timber was treated with, which can be identified by analysis. The Code of Practice in Related Links gives recommended advice on how treated timber can be disposed of effectively.Tanalised E may be burned in approved industrial incinerators, but should not be burned in open fires or home wood burners. Please see the Related Link for more detailed information.When burned, Tanalised C or CCA treated timber releases toxic chemicals into the air and concentrates them in the ash. The treatment of this timber may incorporate Copper, Chrome and Arsenic. These can all be classed as heavy metal toxins. Symptoms will vary depending on the degree of poisoning but can include:loss of appetite,nausea,vomiting,diarrhoea,skin tingling,cramping of muscles,seizures,hearing loss,sleepiness,confusion,headaches,fainting,dizziness.
Is timber the best wood used?
no the best wood is treated mahogony
How do you tanalise timber?
Timber is 'TANALISED' (treated) in an industrial treatment vessel using TANALITH preservative applied using vacuum pressure technology. TANALITH and TANALISED are registered trade marks of the preservative manufacturer, Arch Timber Protection, and may only be used to describe industrial timber treatment using TANALITH preservative. The treatment process consists of 5 stages: 1. Timber is loaded into the treatment vessel. An initial vacuum is applied, and the timber cells are evacuated of air. This vacuum is held. 2. The cylinder is flooded under vacuum with TANALITH wood preservative. 3. Hydraulic pressure is applied, forcing the preservative deep into the structure of the timber. 4. A final vacuum extracts excess preservative solution, which is then pumped back into storage. 5. Low pressure inside timber draws in surface solution when vented to atmosphere. The treated timber is then left to dry - a minimum holding time of 48 hours is recommended. In Europe, TANALITH E preservative is used, which contains copper and triazole biocides, which are commonly used to protect food crops. TANALISED E pressure treated timber can be used in a range of applications, from construction timbers through to heavy duty, highway fencing applications, where a desired service life of 15 years plus can reasonably be expected. Note that where TANALISED treated timber is cross cut, notched or bored following treatment, liberal coating of ENSELE end grain preservative is required to maintain the integrity of the preservative system. Further information on TANALITH E and the treatment process can be found on the Arch Timber Protection website at www.archtp.com. General information regarding timber treatments is available on the Wikipedia site: http://en.wikipedia.org/wiki/wood_preservation
Will Greenwood untreated timber rot if it is set into cement to form a foundation support on outdoor decking?
To set untreated timber in cement is asking trouble. Only pressure treated lumber should be used as a foundation support for outdoor decking. Greenwood can also lose its original shape.
Why you collect soil samples away from fences?
Most fence timber is treated, if you test the soil close to it there is a good chance the soil will be contaminated from the timber preservative leaching from the timber to the soil.
