0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What do you mean by dynamic seal of pump?
dynamic seal of pump means seal which prevents the leakage of fluid from pump shaft
What is a Monoblock pumps?
A Monobloc pump is a pump in which all rotating parts are mounted on a common shaft. The main components of a Monobloc pumps are Pump assembly and Motor assembly. Since there are 7% losses in belt driven sets and 3% losses in coupling driven sets hence to avoid these transmission losses Monobloc pump sets evolved. In monobloc pump sets as motor and pump are mounted on a single shaft there is no energy loss during energy transmission from motor to shaft.­­­­­­­­ By - Tanveer Ahmed Bankapur
What are the spare parts of centrifugal pump?
It depends on the specific pump. For most: the impeller, the wear ring & mechanical seal. In a pump with a packed stuffing box, the packing. In some pumps, the shaft coupling.
Formula of motor shaft power for pumps?
Power available at shaft of pump Ps = p x g x Q x h where, p=density of fluid g= gravitational acceleration Q= discharge of fluid in m3/sec h= differential head of pump
What is the purpose of o rings?
They are used to seal motors or machines and rotatin pump shaft or hydraulic cylinder pistons.
What is the best material for submersible pump shaft?
Yeah, the best material simply pump shaft. I guess that pumping shaft's just the way it is
What drives the water pump on a 1983 750 shadow?
The water pump is driven by the oil pump shaft - there is a tab on the end of the oil pump shaft and there is a groove on the water pump which sits into that shaft. All shafts end up being driven by the motor.
Does a 1994 Chevy 350 have a long or short shaft water pump?
That would be a long shaft water pump.
Is a drive shaft anything to do with a crank shaft?
well a cranks shaft u need a hand to pump its the same as petrol because when u pump it A WIERD SUBSTANCES EJACULATES FROM IT :)
How can you tell if the water pump on a 2002 Daewoo Leganza is going out?
Leaking around water pump mounting or shaft Play in shaft
What is shaft alignment of a pump?
The alignment of a pump is the process of making sure the pump shaft and prime mover (electric motor, engine,ect.)shaft are lined up perfect both horazonally and verticaly to ensure there is no binding on the coupling.
What causes the oil pump not to pick up?
Shaft from distributor could be stripped or the screen on oil pump my be clogged but most likely its the shaft coming from pump to the distributor is stripped or broke
Can you miss the fuel pump rod on a 350 Chevy?
yes you can. of you tightened it up off the shaft pump damage probably occured or the shaft has bent.
How do you remove the fan from the water pump shaft on a Chevy Cheyenne pickup with a V6?
Pull the radiator shroud, remove the serpentine belt, remove the fan from the water pump shaft, then remove the water pump.
Does crank shaft senor engage fuel pump in anyway?
No, fuel pump is controlled by fuel pump relay.
What are the names of the principle parts of a centrifugal pump?
The principle parts of a centrifugal pump are the pump casing, also called a volute, and the impeller. The other parts are the pump shaft, bearing(s), shaft seal, the wear rings, and the inlet and outlet. The impeller is mounted on the pump shaft. The pump shaft is coupled to an external power source like a motor. The motor turns the shaft, the shaft makes the impeller turn and the fluid being pumped is put in motion. The volute causes a change in pressure in the fluid. The shaft seal stops the fluid from leaking out of the casing (volute). The wear rings separate the high and low pressure areas inside the casing. The bearing(s) make the shaft turn easier. The inlet and outlet parts of the casing connect to the fluid piping system.
What is a overhung pump?
A centrifugal pump whose impeller is mounted on the end of a shaft that overhangs its bearings.
