0
what kind of car and what motor??
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where are the timing marks on a 1992 Toyota Paseo 16 efi 1.5 liter engine?
Where are the timing marks on a 1992 Toyota Paseo 16 efi 1.5 liter engine?
Timing marks 1996 geo tracker 1.6l 16 valve?
The 1996 Geo Tracker 1.6 liter engine timing marks can be found on the outside of the main pulley. The timing marks will be scattered around the pulley.
Where do you locate the thermostat on a 1988 Pontiac lemans 16 liter?
IT'S IN THE HOUSING BEHIND THE TIMING COVER THAT THE UPPER RAD HOSE CONNECTS TO.
How do you Align timing marks 94 Pontiac sunbird?
there should be markings on your timing cover that range from 0 to 16, the flywheel mark needs to be in the center at 8. then the cam pulley mark needs to line up with the groove on the backing plate.
How do you change a timing belt on a Isuzu axiom?
Disconnect battery ground cable.Remove air cleaner assembly.Remove radiator upper fan shroud from radiator.Move drive belt tensioner to loose side using wrench then remove drive belt.Remove cooling fan assembly four nuts, then the cooling fan assembly.Remove cooling fan drive pulley assembly.Remove idle pulley assembly.Remove serpentine belt tensioner assembly.Remove power steering pump assembly.Remove crankshaft pulley assembly using J-8614-01 crankshaft holder, hold crankshaft pulley remove center bolt, then the pulley.Remove right side timing belt cover then left side timing belt cover.Remove lower timing belt coverRemove pusher. Caution: The pusher prevents air from entering the oil chamber. Its rod must always be facing upward.Remove timing belt. Caution:1 Do not bend or twist the belt, otherwise its core could be damaged. The belt should not tee bent et a radius less than 30 mm (1.1811 inch). 2 Do not allow oil or other chemical substances to come in contact with the belt. They will shorten the life. 3 Do not attempt to pry or stretch the belt with a screw driver or any other tool during installation. 4 Store timing belt in a cool and dark place. Never expose the belt direct sunlight or heat InstallationNote: For correct belt installation, letter on the belt must be able to be read as viewed from the front of the vehicle.Install timing belt.1 Align groove of crankshaft timing pulley (2) with mark on oil pump (1).Align the mark on the crankshaft timing pulley (3) with alignment mark (white dotted line) on the timing belt (4).Secure the belt with a double clip or equivalent clip. Note: When timing marks are aligned, No.2 piston will be on Top Dead Center.2 Align the alignment mark on the RH bank camshaft drive pulley (2) to the alignment mark of the cylinder head cover RH (3). The camshaft pulley alignment mark should also align with alignment mark on the cylinder head cover.It may require up to four revolutions of the camshaft pulley to achieve alignment of all marks.3 Align the alignment mark (white line) on the timing belt (1) with alignment mark on the RH bank camshaft drive pulley (2) (on the left side as viewed from the front of the vehicle) and put the timing belt on the camshaft drive pulley.Secure the belt with a double clip or equivalent clip. 4 Align the alignment mark on the LH bank camshaft drive pulley (2) to the alignment mark of the cylinder head cover LH (3). The camshaft pulley alignment mark should also align with alignment mark on the cylinder head cover.It may require up to four revolutions of the camshaft pulley to achieve alignment of all marks.5 Align the alignment mark (white line) on the timing belt (1) with the alignment mark on the LH bank camshaft drive pulley (2).When aligning the timing marks, use a wrench to turn the camshaft drive pulley, then set the timing mark between timing belt and camshaft drive pulley and put the timing belt on the camshaft drive pulley.Secure the belt with a double clip or equivalent clip. Note: It is recommended for easy installation the belt be secured with a double clip or equivalent clips after it is installed to each pulley.6 Install crankshaft pulley temporarily and tighten center bolt by hand (do not use a wrench).Turn the crankshaft pulley clockwise to give some belt slack between the crankshaft timing pulley and the RH bank camshaft drive pulley.Install pusher and tighten bolt to the specified torque. Torque: 25 Nm (2.5 kgf-m/18 ft. lbs.)1 Install the pusher while pushing the tension pulley to the belt. 2 Pull out pin from the pusher. Note: When reusing the pusher, press the pusher with approximately 100Kg to retract the rod, and insert a pin (1.4 mm (0.055 inch) piano wire).After release the push rod from the locking pin, the rod projection is approximate 5 mm (0.1969 inch).3 Remove double clips or equivalent clips from timing belt pulleys.Turn the crankshaft pulley by six turns and check for timing mark alignment.Install timing belt cover. Remove crankshaft pulley that was installed in step 1 item 5. Tighten bolts to the specified torque. Torque: 9 Nm (14 ft. lbs.)Install crankshaft pulley using J-8614-01, hold the crankshaft pulley and tighten center bolt to the specified torque. Torque: 167 Nm (123 ft. lbs.)Install fan pulley bracket and tighten fixing bolts to the specified torque. Torque: 22 Nm (16 ft. lbs.)Install power steering pump assembly and tighten to the specified torque. Torque: M8 bolt: 22 Nm (16 ft. lbs.) M10 bolt: 46 Nm (34 ft. lbs.)Install cooling fan assembly and tighten bolts/nuts to the specified torque. Torque: 22 Nm (16 ft. lbs.) for fan pulley and fan bracket. Torque: 7.5 Nm (66.4 inch lbs.) for fan and clutch assembly.Move drive belt tensioner to loose side using wrench, then install drive belt to normal position.Install radiator upper fan shroud.Install air cleaner assembly.
What are the release dates for School of Golf - 2011 Chapter 16 Setup and Alignment 1-16?
School of Golf - 2011 Chapter 16 Setup and Alignment 1-16 was released on: USA: 31 May 2011
What is the correct timing for a 1977 Lincoln mark V 460ci do i have to plug up the vacunm advance line?
Mine says 16 degrees and yes I believe you do.
What are 16 ounces to a liter?
16 US fluid ounces = 0.473 Liters.
Where do you set the timing marks on the cam shaft pulley and the crank shaft pulley for a 1990 Geo Storm 16?
Crankshaft timing mark should be lined up with the triangle on the oil pump cover (at 12:00). Camshaft timing mark should be at 9:00 lined up with the cylinder head surface, and the dowel should be at 12:00. This is for the SOHC motor
Diagram for timing belt on Holden astra ts 16 valve 1.8 liter where are the timing marks for aholden astra ts?
dunno the marks seem strange to me have just pulled down my missus 1.8 n found when crank pulley mark is showing t.d.c. marks on cam sprockets are pointing at 3 oclock inlet and 9 oclock exhaust so will have to leave it till ive seen a photo sorry mate
How many 16 oz cups in 2 liter of pop?
You will get about 4.2 16-oz cups from a 2-liter pop bottle.
Wheel alignment specs on 2002 Chevy Tahoe you have a 2002 Tahoe with auto ride on it you went form 16 to 18 wheels Is there a different specs on the alignment?
alignment specs are the same unless changing ride height. putting bigger wheels will not alter alignment
