The door panel alone may be 36 inches wide but you also have the side "Door Jambs" which are about 1/2 inch which will add to- and increase your openning size to 37 inches.
Just measure from the outter most edges of the storm door frame to know what your exact openning size needs to be-- when cutting the openning --cut your outter most edges about 1 inch larger than your measurement/ this will add 1/2 inch to both the left and right side of the oppening
and add 1/2 inch to the top or bottom edge of the openning. Ths will allow for easier setting of the complete door frame and easy shimming when leveling the door.
In other words-- From the opennings "L" shape / take off an extra inch from one side and 1 extra inch from the bottom -this wil give you plenty of play space for fitting the entire storm door in easily and usng your shims. Place shims on the top / (sides first) as you center the frame into the openning-- once the top portion is centered add shims to the (midway/ sides) and then to the (bottom / sides) and now you can start using a 2 or 4 foot level to check the straight level of your door frame before screwing it permanently into place.
The standard width for the average entry door in America is 36". That is not including the frame. ADA requires 32" clearance when door is open 90 degrees , which results in using a 36" door due to the thickness of the door and projections from the jambs. Interior doors range in width from 24"-32" in even-number increments. Older homes often have custom widths falling between these numbers. Of these sizes, 30" is the most common in America.
There is not a quote "standard" door width as doors can be purchased in 2" increments. There are a few building code restrictions for minimum width of certain doors. Like an egress door is required to be 36 inches in width for a residence. There can also be minimum widths for handicap accessibility. These doors in a house need to have a clear opening width of 30 inches.
36 inches from the floor
From the IRC 2003 Code: 311.4.3 Landings at doors. There shall be a floor or landing on each side of each exterior door. Exception: Where a stairway of two or fewer risers is located on the exterior side of a door, other than the required exit door, a landing is not required for the exterior side of the door he floor or landing at the exit door required by Section R311.4.1 shall not be more than 1.5 inches (38 mm) lower than the top of the threshold. The floor or landing at exterior doors other than the exit door required by Section R311.4.1 shall not be required to comply with this requirement but shall have a rise no greater than that permitted in Section R311.5.3. Exception: The landing at an exterior doorway shall not be more than 7 3/4 inches (196 mm) below the top of the threshold, provided the door, other than an exterior storm or screen door does not swing over the landing. The width of each landing shall not be less than the door served. Every landing shall have a minimum dimension of 36 inches (914 mm) measured in the direction of travel.
I haven't kept up with building codes in a number of years, but believe it was 36" minimum landing at bottom or top of stairs. You need to check out the National Building Code to verify. You can Google this information online,check for a copy at your local library or make a call to your local building department.Located a 2009 edition of the IRC-InternationalResidential Code on Stairways. You still need to verify that this information is current and suggest you contact your local building department.STAIRWAYS46. LANDINGS. Section R311 IRC 2009R311.7.5 Landings for stairways.There shall be a floor or landing at the top and bottom of each stairway.Exception:A floor or landing is not required at the top of an interior flight of stairs, including stairs in an enclosed garage, provided a door does not swing over the stairs. A flight of stairs shall not have a vertical rise larger than 12 feet (3658 mm) between floor levels or landings. The width of each landing shall not be less than the width of the stairway served. Every landing shall have a minimum dimension of 36 inches (914 mm) measured in the direction of travel.R311.3 Floors and landings at exterior doors.There shall be a landing or floor on each side of each exterior door. The width of each landing shall not be less than the door served. Every landing shall have a minimum dimension of 36 inches...
The most often chosen width of a front door is 36".
There is actually no actual measurment you will have to measure it for yourself to fin out
39 inch is the standard width of any door of house. 36 is the standard width (3 feet).
no no
Minimum 32 inch. Maximum width of a swinging door leaf is 48 inch. Typically 36 inch installed.
There is no standard door width as they come in 2" increments up to 36" wide. A common door jamb width is 4-9/16" width, this is for a 2x4 wall and 1/2" drywall on both sides.
There is no standard door width as they come in 2" increments up to 36" wide. A common door jamb width is 4-9/16" width, this is for a 2x4 wall and 1/2" drywall on both sides.
36" door, to have access for the handicapped.
36"
The dimensions of an average American front door is 36 inches wide and 80 inches high (3' x 6'-8").
The width of a standard interior door is 32 inches. There are many other standardized sizes ranging from 18 to 36 inches depending on the application.
36 inches IS the width. . .normally doors come in 24, 28, 32, or 36 inch widths, and either 6'8" or 8' height