0
What is the approximate bandwidth of a single sideband voice signal?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is bandwidth required for AM signal?
With full double sideband AM the bandwidth of the modulated signal is twice that of the baseband information signal. With suppressed carrier single sideband AM the bandwidth of the modulated signal is identical to that of the baseband information signal. With vestigial sideband AM the bandwidth of the modulated signal is somewhere between the above two cases, depending on how much of the vestigial sideband is included.
What the difference between single side band single carrier transmission and full carrier AM?
1. Single-sideband transmission requires only half as much bandwidth as double sideband.2. SSBSC require less total transmitted power than full carrier AMIn full carrier AM, the transmitted signal consists of two sidebands (containing the transmitted information) and the carrier signal. Long ago, it was realized that both sidebands contained the same information, and the carrier signal could be supplied by the receiver. Thus, if you suppress transmitting the carrier and one sideband, you can use the available power to increase the power in the remaining sideband.
Which modulation scheme requires the least minimum bandwidth?
Suppressed carrier single sideband amplitude modulation - SCSSBAM.
Am single-sideband full carrier?
single sideband full carrier
What is a SSBSC signal?
Single Side Band Suppressed Carrier. This is a modification of AM (Amplitude Modulation) that both reduces required transmitter power and signal bandwidth. The carrier is first modulated by the signal the same as in ordinary AM, then is sent through a bandpass filter to remove one sideband and the carrier. To demodulate it and recover the original signal the receiver must reinsert the carrier using a BFO (Beat Frequency Oscillator) and Mixer.
How does double sideband differ from standard AM?
Standard AM already has double sideband. When you talk about double sideband, however, often the meaning is usually "double sideband, suppressed carrier". By suppressing the carrier, you can impute more power into the sidebands, because you are not providing power to the carrier, which accounts for a significant percentage of the total power. Since the sidebands actually contain the signal, you can boost the signal to noise ratio by suppressing the carrier. This comes at a cost, however, in complexity, because you need to regenerate the carrier in order to demodulate the signal. In fact, many systems use single sideband, suppressed carrier, doubling the available power to the sideband containing the signal over double sideband suppressed carrier. This works, again at the cost of receiver and transmitter complexity, because the two sidebands contain the same information.
How does single sideband differ from standard AM?
Single Sideband is effectively the same as standard AM, except that the carrier and one of the two sidebands is suppressed. This allows you to put more power into the information carrying part of the signal, at the complexity of having additional circuitry on both ends to modulate and demodulate.
What is vestigial side band transmission?
Vestigial sideband (VSB) is a type of amplitude modulation ( AM ) technique (sometimes called VSB-AM ) that encodes data by varying the amplitude of a single carrier frequency . Portions of one of the redundant sidebands are removed to form a vestigial sideband signal - so-called because a vestige of the sideband remains.
What is mean by full carrier?
At this point we're talking about amplitude modulation. If you're transmitting with "29.000" MHz displaying on your radio's frequency display and your bandwidth is set to 4 kHz, you are transmitting useful intelligence from 28.996MHz to 29.004MHz--4KHz on each side of the carrier--in "full carrier" or "double sideband" mode. You wouldn't actually transmit this for a couple of reasons. The most important reason is that using filters in your radio to remove either the signal below 29MHz (called "upper sideband" or USB operation) or the signal above it (called "lower sideband" or LSB) allows another operator to use the piece of spectrum you relinquished. The other advantage is SSB makes more efficient use of your amplifier, so you can talk to people farther away from you and they can hear you better. So..."full carrier" means double sideband, and then there's single sideband.
How single sideband is being generated?
In regards to the radio transmission mode, SSB is an improvement of AM, and there are generally three ways single sideband can be generated -- filtering out the unwanted sideband and suppressing the carrier; using phasing to suppress the unwanted sideband and carrier (Hartley modulator); or quadrature mixing and filtering (Weaver modulator).
What are the advantages and disadvantages of double sideband suppressed carrier modulation?
Amplitude modulation of a carrier results in a transmitted signal consisting of the carrier, plus an 'upper sideband' and a 'lower sideband', spaced above and below the carrier frequency by the frequency of the modulation.The bandwidth of the whole signal is double the modulation frequency. Also, the power in the carrier is constant, and power must be added in order to radiate the sidebands.All the receiver needs in order to extract the information from the signal is one complete sideband, and knowledge of the frequency and phase of the carrier. Economically speaking, the carrier is wasted power, and the other sideband is wasted power andwasted spectrum.If you can filter away one of the sidebands before transmission, then you save half of the occupied spectrum, and the receiver has everything it needs to decode the signal. If you can also filter away the carrier ... or at least knock it way down ... before transmission, you can save a lot of power and use it for the remaining sideband, which extends your range for a given amount of power. The receiver still has everything it needs, as long as it can pick up a sniff of carrier ... enough to derive the carrier frequency and phase.This mode is known as "Single Sideband Suppressed Carrier". It's exactly how the video portion of standard NTSC analog TV was transmitted, throughout all of human history until June 2009.
What is analog modulation?
Analog modulationIn analog modulation, the modulation is applied continuously in response to the analog information signal.Common analog modulation techniques are:Amplitude modulation (AM) (here the amplitude of the modulated signal is varied) Double-sideband modulation (DSB) Double-sideband modulation with unsuppressed carrier (DSB-WC) (used on the AM radio broadcasting band)Double-sideband suppressed-carrier transmission (DSB-SC)Double-sideband reduced carrier transmission (DSB-RC)Single-sideband modulation (SSB, or SSB-AM), SSB with carrier (SSB-WC)SSB suppressed carrier modulation (SSB-SC)Vestigial sideband modulation (VSB, or VSB-AM)Quadrature amplitude modulation (QAM)Angle modulation Frequency modulation (FM) (here the frequency of the modulated signal is varied)Phase modulation (PM) (here the phase shift of the modulated signal is varied)
