0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is a gas turbine compressor bleed valve?
Bleed Valve FunctionValve which is meant to siphon off a portion of the flow from another system.A heavy-duty gas turbine employs compressor bleed valves to protect the axial compressor during start-up and shutdown against stalling and surging conditions. These valves are typically only open during acceleration to rated speed and deceleration from rated speed. Newer heavy-duty gas turbine with complex combustion system arrangements designed to limit emission of harmful gases also employ the compressor bleed valves during very light loading to limit the amount of air entering the combustor.Compressor bleed valves discharge into the gas turbine exhaust duct. Compressor bleed valves are generally closed during normal operation (with the previous exception) since "dumping" axial compressor discharge into the exhaust reduces efficiency (but it's MANDATORY during start-up and acceleration to protect the compressor!). Compressor bleed valves are generally either fully open or fully closed; they are not modulated.Heavy-duty gas turbines also employ inlet bleed heat valves to recirculate a portion of the axial compressor discharge back to the inlet of the axial compressor for a variety of functions. One application uses them to heat the inlet air to prevent icing on the compressor inlet (appropriately called anti-icing protection); another application uses inlet bleed heat to protect the axial compressor when the IGVs (axial compressor Inlet Guide Vanes) are closed below the "normal" operating conditions ("normal" being before complicated combustion systems designed to limit exhaust emissions were invented).Inlet bleed heat control valves are modulated to control the amount of air recirculated back to the axial compressor inlet. Recirculating axial compressor discharge back to the inlet is also inefficient, but is generally limited to approximately 5% of rated air flow through the compressor--and necessary to protect the compressor at low IGV angles. Inlet bleed heat valves are generally closed before the unit reaches rated load (except for anti-icing protection) and should be closed during rated power output (Base Load) operation (except for anti-icing protection).
Do you have to bleed the air bags to change the compressor?
We changed compressor, put in new air bags, and car sits sideways. What needs to be bled? 1996 Lincoln Twncar.
Do you replace Hydraulic Line To Suspension Pump when replacing compressor?
no you do not yo may have to bleed out all the air
How do you lubricate the compressor for air brakes?
In a gear driven compressor which is integral to the engine (as is the case with heavy duty trucks), you don't - the motor oil flows through the compressor, lubricating it. That's why it's also a telltale sign that the compressor is bad if you bleed the air tanks and have oil coming out.
How do you bleed air from a power steering pump in a 1993 ford probe?
put an air compressor hose on one end
Will putting a dragging metal strap from your car stop static shock when you exit the car?
Yes it will. BUT a metal strap could create sparkle which could be a hazard. Use instead a black carbon rich rubber grounding strap. It will bleed off the static charge. Gas tankers are equipped with those straps to prevent ESD.
How do you correct when a compressor has lock up due to liquid charging?
Bleed off some of the refrigerant to get the system pressure down, then wait a while until any liquid refrigerant in the compressor has time to leak into the refrigerant loop. It may take a few minutes; since the compressor valves seal imperfectly, pressures will eventually equalize and it should be possible to start up the compressor again.
What is the syllable for strap?
There is only 1 syllable in "strap."
What is bleeding of turbine?
Bleed air in gas turbine engines is compressed air taken from within the engine, after the compressor stage(s) and before the fuel is injected in the burner
How do you bleed a sprinkler system?
Bleeding a sprinkler system involves draining the existing water from the pipes. Afterwards, the pipes should be completely dried by using an air compressor.
What are some styles of ankle strap sandals?
There are many different types of ankle strap sandals, like the evening ankle strap, the rhinestone ankle strap, flat ankle strap, Gucci ankle strap, and many more.
What bag is good for school?
Kindergarten- wheeler back packs 1st- 2 strap 2nd-2 strap 3rd-2 strap 4th-2 strap 5th-2 strap 6th- Book bag or 1 strap
