0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How To Choose A Plasma Cutter?
A plasma cutter sounds like a futuristic tool from a science fiction novel, but in reality they are used all the time. The cutter consists of a nozzle through which compressed gas is forced through. A small ignition unit called an electrode provides a spark which sets the gas on fire. The gas quickly becomes superheated and a small portion of it turns into plasma. Plasma is gas that has become partially ionized. Due to the incredible heat required for this to happen, plasma is always found at superheated temperatures. Thanks to the heat, the plasma cuts right through the metal. The gas is negatively charged due to the negatively charged electrode. Since the metal being cut is positively charged, this provides additional cutting power. Choosing a plasma cutter is partially determined by the area of the workshop in question. The relative power of a cutter is measured in the rate, or how much metal a cutter can cut per minute. The rate is a result of two factors: the amperage of the cutter and the type of metal. Different types of metals conduct electricity faster or slower. Amperage is the measure of how strong power-wise the cutter is. The higher the amperage, the stronger the electrical spark and therefore the stronger cutting power of the plasma. Typical rates for plasma cutters range from eight to twelve inches of metal per minute. The electrical output of the workshop must also be taken into account. Plasma cutters can handle different levels of voltage; for instance, do not buy a plasma cutter with a 110-volt plug if your workshop can put out anything above 110 volts. Higher-voltage cutters produce more amperage, so they can cut through thicker metals. Cutters also have limits known as duty cycles. A cutter’s duty cycle is the number of minutes it can continuously cut before it needs to cool down. These cycles are measured in terms of percentages; for example, if the cutter can cut for two minutes but needs eight to cool down, it has a duty cycle of twenty percent. Finally, the cost must be considered, as well. Depending on the amperage, a plasma cutter can cost anywhere from four hundred to seven thousand dollars.
How to Use a Plasma Cutter?
A plasma cutter is a device that uses compressed air or an inert gas blown through a high speed nozzle to cut metal. As the inert gas or compressed air is blown out of the nozzle, an electric arc is formed from the nozzle to the surface of the material being cut. Some of the inert gas or compressed air is converted into plasma as it touches the material being cut, and the heat from this plasma is used to cut the metal. There are two types of plasma cutters most commonly used in commercial applications. The HF (high frequency) Contact plasma cutter initiates an arc by using a high frequency, high-voltage spark to ionise the air through the torch head. While the use of this method is quite common, it is not suitable for CNC cutting applications because it requires the torch to be in contact with the material that is being cut. The other method commonly used in commerical applications is the Pilot Arc method. This method uses a high-voltage, low current circuit to create a spark within the torch body. The creation of this spark generates a pocket of plasma gas, or a pilot arc. The pilot arc is able to maintain itself because there is a return electrical path in the torch head. The pilot arc is maintained until the torch comes into contact with the material being cut, at which time the main plasma cutting arc is ignited. Because this method does not require the torch to be in contact with the material it is cutting in order to ignite, this type of plasma cutter is used across all plasma cutter applications. Over the last decade, manufacturers of plasma cutters have continued to roll out new models that feature smaller nozzles and thinner plasma arcs. As these components have become smaller, plasma cutters have been reduced in size to the point where there are now hand-held plasma cutters. This development has made plasma cutters not only easier to handle, but also much more precise. Another benefit of the increasing miniaturization of plasma cutters has been a reduction in their cost. This reduction in cost has now made the purchase of a plasma cutter within the reach of most hobbyists.
Where can I get snow plows in Missouri?
Snow plows can be found in Missouri at Cost Cutter Snowplows in Pevely. Cost Cutter has more information at http://www.costcutterssales.com/.
How do you cut video for free?
Cutting video for free requires a cost-free video cutter, like Joyoshare Video Cutter, Avidemux, Cute Video Cutter Free, Free Video Cutter, Shotcut, Online Video Cutter, Clideo, etc.
Where do you get snap back hats from?
You can get snap back hats at the shopping centre, Beach City and Footlocker. Fake snap back cost $10 dollars to $30 dollars. Real snap back cost more than $70 dollars.
How much does a plasma lift cost?
A plasma lift cost varies on its size and length. Usually it costs from $200 to $500. Plasma lifts can be found at all electronic stores like Best Buy and Fry's.
What does a plasma television cost compared to a LCD television?
When plasma televisions were new to the market, their cost was quite a deal more than their LCD counterparts, but these days, as they become more commonplace, their cost discrepancy is dropping. It's not hard to find plasma screens at low prices.
How much do snap peas cost?
Check your local listings.
How much does a plasma screen tv cost online?
A PLASMA 42 INCH TV ONLINE IS $419.00.A PLASMA WITH HDTV IS $749.00.A PLASMA WITH A BUNDLE PACK IS $649.00.A PLASMA WITH BUILT IN WI-FI IS $944.00.YOU CAN FIND THIS ON NETTAG.
How much does plasma cost?
Plasma cutters can cost from anywhere from 100 dollars to 1000 dollars for the better cutters. If you want to buy some you should go to a hardware store.
How much does it cost to purchase a laser cutter online?
A laser cutter is a generic term for a broad range of machines with a broad range of capabilities. A machine shop laser cutter costs in excess of 30000$. A much less capable machine will run about 4500$.
What is the difference between between snap on and blue point?
Aside from cost, Snap-On tools are made by or directly for Snap-On... Blue Point are typically tools from another manufacturer which are badge engineered for Snap-On under the Blue Point name, but which fall under the same warranty as Snap-On tools.
