0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is pvid?
A Port VLAN ID (pvid) is a default VLAN ID that is assigned to an access port to designate the virtual LAN segment to which this port is connected. The pvid places the port into the set of ports that are connected under the designated VLAN ID. Also, if a trunk port has not been configured with any VLAN memberships, the virtual switch's Port VLAN ID (pvid) becomes the default VLAN ID for the ports connection.
What are two characteristics of VLAN1 in a default switch configuration?
VLAN 1 is the management VLAN. All switch ports are members of VLAN1.
Can STP be configured on an HP server?
Configuring Standard STP Parameters STP is disabled by default on Routing Switches. By default, each port-based VLAN on an HP device runs a separate spanning tree (a separate instance of STP). An HP device has one port-based VLAN (VLAN 1) by default that contains all the device's ports.
Why would packets from the router or hosts fail when trying to reach the switch management interfaces if the native VLAN were left in default?
The native VLAN is untagged. If the VLAN 99 traffic to the router is untagged (as it would be, because that is native on the switches), the router cannot interpret the data because there is no VLAN information in the header as expected. In turn, the router tags all VLAN 99 traffic outbound, and leaves VLAN 1 data untagged, so the switches are unable to correctly interpret either. VLAN traffic to the other VLANs should not be affected by the assignment of the native VLAN.
A network administrator implements inter-VLAN routing by configuring subinterfaces on a router What is one important fact that must considered?
The IP address of each router subinterface mist be used as the default gateway for hosts on the corresponding VLAN.
What does VLAN stand for?
A VLAN is a virtual LAN. In technical terms, a VLAN is a broadcast domain created by switches. Normally, it is a router creating that broadcast domain. With VLANs, a switch can create the broadcast domain. This works by, you, the administrator, putting some switch ports in a VLAN other than 1, the default VLAN. All ports in a single VLAN are in a single broadcast domain. Because switches can talk to each other, some ports on switch A can be in VLAN 10 and other ports on switch B can be in VLAN 10. Broadcasts between these devices will not be seen on any other port in any other VLAN, other than 10. However, these devices can all communicate because they are on the same VLAN. Without additional configuration, they would not be able to communicate with any other devices, not in their VLAN.
How many different vlan's can an 802.1Q trunk support?
There may be a more general answer to this, but by default most Cisco hardware will support up to 1,000 VLANs.
Which set of commands will enable a network administrator to remotely manage a LAN switch?
Switch(config)# ip default-gateway 192.168.1.254Switch(config)# interface vlan 1Switch(config-if)# ip address 192.168.1.1 255.255.255.0Switch(config-if)# interface fa0/1Switch(config-if)# switchport access vlan 1
How do you connect computers on separate VLAN?
Since VLAN's cannot communicate with other VLAN's directly, I believe you would have to set up a router to do that. I would check out how to set up a bridge between two VLAN's.
how are packets assigned to the VLAN?
VLAN: How are packets distributed with respect to the different classifications?
What is a function or characteristic of the native VLAN?
It is the VLAN that supports untagged traffic on an 802.1Q trunk
The network administrator needs to remove the east-hosts vlan and use the switch port from that vlan in one of the existing vlans what two commands should be used when completely removing vlan 2 from?
no vlan XXX copy run star
