answersLogoWhite

0

The connecting wire will be thicker and made of a low resistance material to allow electricity to flow with minimal losses. The element requires a thinner wire with higher resistivity which causes it to heat when electricity passes through.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How can I replace a dryer heating element?

To replace a dryer heating element, first unplug the dryer and remove the back panel. Locate the heating element, disconnect the wires, and remove the old element. Install the new heating element by connecting the wires and securing it in place. Finally, reattach the back panel and plug in the dryer to test the new heating element.


How would you megger a heating element?

To megger a heating element, first ensure the element is disconnected from any power source to avoid electrical shock. Use a megohmmeter to measure insulation resistance by connecting one lead to the heating element terminal and the other lead to the element's metal casing or ground. Activate the megger to apply a test voltage (commonly 500V) and read the insulation resistance value; a good heating element typically shows a resistance of 1 MΩ or higher. If the reading is significantly lower, it indicates potential insulation failure.


What is the process for replacing the Frigidaire electric oven heating element?

To replace the Frigidaire electric oven heating element, first turn off the power to the oven. Remove the screws holding the old element in place and disconnect the wires. Install the new element by connecting the wires and securing it with screws. Turn the power back on and test the oven to ensure the new element is working properly.


When checking an electric heating element you read voltage but no amperage What can you determine about the heating element?

If you are reading voltage but no amperage on the heating element, it suggests that there is a break in the circuit within the heating element, preventing current flow. This could be due to a burnt-out heating element or a disconnected wire. The heating element likely needs to be replaced.


What is the difference between a heating curve and a cooling curve?

heating curve is hotter than the cooling curve


How to change Black and Decker toaster oven tro700series heating element?

To change the heating element in a Black and Decker toaster oven from the TRO700 series, first, unplug the toaster oven and allow it to cool completely. Remove the screws on the back panel to access the heating element, disconnect the wires attached to it, and carefully pull it out. Replace it with a new heating element by connecting the wires and securing it in place, then reattach the back panel and plug in the toaster oven to test it. Always consult the user manual for specific instructions and safety precautions.


Does a gas dryer have a heating element?

Yes heating element is burner assembly.


How can I test the dryer heating element to determine if it is functioning properly?

To test the dryer heating element, you can use a multimeter set to the ohms setting. Disconnect the dryer from the power source and locate the heating element. Remove the wires connected to the heating element and place the multimeter probes on the terminals of the heating element. If the multimeter reads a low resistance, the heating element is functioning properly. If the reading is high or infinite, the heating element may be faulty and needs to be replaced.


What is difference between heating things and burning things?

Heating is basically warming something at a lower temperature and burning is heating something at a high temperature.


What is the difference between hvdc and HVAC?

HVDC is a programmer for heating and air. The HVAC is the installer for heating and air. I have a license for both of them,


How can I change the heating element in my dryer?

To change the heating element in your dryer, first unplug the dryer and locate the heating element. Remove the back panel of the dryer and disconnect the wires attached to the heating element. Take out the old heating element and replace it with a new one. Reconnect the wires and put the back panel back on. Plug in the dryer and test it to ensure the new heating element is working properly.


How can I replace the heating element in my dryer?

To replace the heating element in your dryer, first unplug the dryer and locate the heating element. Remove the back panel of the dryer and disconnect the wires attached to the heating element. Take out the old heating element and replace it with a new one. Reconnect the wires and put the back panel back on. Plug in the dryer and test it to ensure the new heating element is working properly.