answersLogoWhite

0


Best Answer
General Motors Driving CycleA complete driving cycle should perform diagnostics on all systems. A complete driving cycle can be done in under fifteen minutes.

To perform an OBDII Driving cycle do the following:

  1. Cold Start. In order to be classified as a cold start the engine coolant temperature must be below 50°C (122°F) and within 6°C (11°F) of the ambient air temperature at startup. Do not leave the key on prior to the cold start or the heated oxygen sensor diagnostic may not run.
  2. Idle. The engine must be run for two and a half minutes with the air conditioner on and rear defroster on. The more electrical load you can apply the better. This will test the O2 heater, Passive Air, Purge "No Flow", Misfire and if closed loop is achieved, Fuel Trim.
  3. Accelerate. Turn off the air conditioner and all the other loads and apply half throttle until 88km/hr (55mph) is reached. During this time the Misfire, Fuel Trim, and Purge Flow diagnostics will be performed.
  4. Hold Steady Speed. Hold a steady speed of 88km/hr (55mph) for 3 minutes. During this time the O2 response, air Intrusive, EGR, Purge, Misfire, and Fuel Trim diagnostics will be performed.
  5. Decelerate. Let off the accelerator pedal. Do not shift, touch the brake or clutch. It is important to let the vehicle coast along gradually slowing down to 32km/hr (20 mph). During this time the EGR, Purge and Fuel Trim diagnostics will be performed.
  6. Accelerate. Accelerate at 3/4 throttle until 88-96 km/hr (55-60mph). This will perform the same diagnostics as in step 3.
  7. Hold Steady Speed. Hold a steady speed of 88km/hr (55mph) for five minutes. During this time, in addition to the diagnostics performed in step 4, the catalyst monitor diagnostics will be performed. If the catalyst is marginal or the battery has been disconnected, it may take 5 complete driving cycles to determine the state of the catalyst.
  8. Decelerate. This will perform the same diagnostics as in step 5. Again, don't press the clutch or brakes or shift gears.
User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the drive cycle on a 1998 Chevrolet pickup?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What year was Chevrolet pickup approximatly 8000.00?

1998 chevy 1500 4 wheel drive 185.000 miles


Spark knock on 1998 Chevrolet Pickup?

Spark plug knock on a 1998 Chevrolet pickup is an indicator that the ignition timing is correct. By adjusting the timing, the knock can be eliminated.


Will a rear window out of a 1998 Chevrolet pickup fit a 2002 Chevrolet pick up?

No it will not.


How do you install the distributor on a 1998 Chevrolet pickup?

I really don't know.sorry.


Where is the fuel shut off switch in a 1998 Chevrolet pickup?

Chevrolet does not use inertia/reset switches.


What sort of vehicle is the Chevrolet Silverado 1500 SS?

The Chevrolet Silverado 1500 SS is a pickup truck. Specifically, it is a really big pickup truck. Chevrolet first started manufacturing the Silverado back in 1998.


Does a 1998 Chevrolet pickup have struts or all shocks?

4 shocks ONLY, NO struts.


Drive cycle for 1998 Saturn sl2?

SEE OBD II drive cycle


What is the drive cycle for 1998 Pontiac Grand Am?

drive cycle for 1998 pontiac grand prix, 3.8 engine, no super charge?


What is the freon capacity on a 1998 2500 Chevrolet?

The 1998 Chevrolet 2500 pickup truck has a Freon capacity of 5.5 pounds. You should never overfill the Freon in your cooling system.


What vehicle does a Fram oil filter PH 3535 fit?

My old notes show it was for a 1998 chevrolet pickup- I think that pickup was a 6.0 liter


How do you make horn stop blowing in 1998 Chevrolet 2500 pickup?

most of them will unplus in the front of the stering wheel