0
The glass bulb of a light bulb is known as the globe. It is made from a thin layer of glass to ensure light efficiency and still support the rest of the bulb.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What is the function of lamp?
To hold the light bulb at a vertical angle and stop it from falling off.
Dim fluorescent bulb?
No...
What are the subsystems in a lamp?
A subsystem for a lamp would be the bulb because the bulb lets the eye see.
What subsystems are in a lamp?
A subsystem for a lamp would be the bulb because the bulb lets the eye see.
Can you put a fluorescent bulb in your floor lamp?
Yes, you can put a fluorescent light bulb in your floor lamp. You need to see what size bulb the lamp takes, but most sizes can be purchased as florescent bulbs.
How do you change a bulb in the multi function display unit of a 307?
You can change a bulb in the multi function display unit of a 307 by first making sure that the lamp is turned off. Then unscrew the bulb and remove it from the lamp.
What is the name of the lamp under glass slide of a microscope?
The lamp under the glass slid of the microscope is called the "bulb" lol. just kidding. i have no idea.
What is the function of lamp?
To hold the light bulb at a vertical angle and stop it from falling off.
How do you change the bulb in a lava lamp?
Remove the lava lamp by lifting up the glass. It separates from the base because it just sits in it. Unscrew the old bulb and screw another one in. When you remove the bulb you will notice that the bulb and base may not be the size of a standard household bulb. On the inside of the base, or the bottom of the base, there should be information about the type and wattage of the bulb. You need to get the same type of bulb to insure that the bulb base will screw into the socket. The wrong type bulb may not fit in the socket or the bulb may be too large and the top of the lamp will not fit properly on the base. If you get the wrong wattage, the bulb may not be hot enough or to hit to make the bulb function properly.
Function of lamp holder?
to hold the light bulb at a vertical angel and stop it from falling off.
When was the first light bulb invented?
The first glass light bulb was invented in 1841 by Frederick DeMoleyns. However the first electric lamp was invented in 1806.
Difference between a lamp and a bulb?
Lamp have required high rating to glow & have a specific luminus area.exa-table lamp,florucent lamp,sodium vapur lamp,BUT but bulb have no required rating exa- halogin bulb
What will happen if you try to complete a circuit by joining the glass of a light bulb?
The glass envelope of a light bulb (which is called an incandescent lamp) is an insulator, and it won't conduct electricity except under the most extreme conditions. Connecting wires to the glass envelope won't complete an electrical circuit.That glass envelope is used to seal the inside of the lamp from outside air, which, if allowed in, would allow the filament to burn up in a second or two. In that light, the glass envelope both electrically insulates the lamp, and also isolates the filament from air (or the oxygen in it) to keep it from burning up.
What is the function of the choke in a hpsv lamp?
The function of any ballast in a lighting fixture is to raise the voltage high enough to strike an arc through the bulb or tube.
Dim fluorescent bulb?
No...
How do you replace license plate bulb on a 2000 dodge neon?
== # Remove screws attaching license plate lamp to rear bumper # Remove lamp from bumper. # Remove bulb socket from lamp. # Pull bulb from socket. == # Install bulb into socket. # Install bulb socket into lamp. # Place lamp in position. # Install screws attaching license plate lamp to rear bumper.
What are the subsystems in a lamp?
A subsystem for a lamp would be the bulb because the bulb lets the eye see.
