0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you calculate pressure ratio of compressor?
Inlet pressure/discharge pressure
What is an inlet valve?
Inlet Valve is comprised of 2 words i.e. Inlet & Valve. Therefore Inlet Valve is that valve through which fuel or a mixture whose pressure in increased by reducing its volume in intaked into the cylinder.
Where is the inlet and outlet of your pressure tank?
A pressure tank for a pump & well potable water system only has one connection. To connect the pump and tank to your house's water inlet, simply connect the tank and pump together with pressure rated pipe, SCH 40 PVC works fine. In that line, cut in a TEE fitting, and from that T, connect the house inlet with a valve to shut the water off.
How do you calculate the exit pressure of a nozzle?
How to calculate the ratio of the inlet-to-exit area of the nozzle
Comparison between impulse and reaction turbines?
in the case of impule turbine total energy at inlet is kinetic energy and in case reaction turbine energy at inlet is kinetic and pressure......
How do you calculate pressure ratio of compressor?
Inlet pressure/discharge pressure
For the same size of pipe when mass flow rate is also same what will happen to the pressure drop if change in inlet pressure takes place?
If you change the inlet pressure, you outlet pressure will also change dramatically.
What is golden joint?
when there is restriction in the pipeline spool so that it can not be hydro tested (ex 1. The pipeline is hydro tested up to a pump inlet and the inlet joint is welded after hydro test. 2. the pipeline is getting connected to a header and the header gets connected to lot of branches where hydro test cant be done) the joints in the loop will be taken 100% radiography and all those joints are called as golden joints Balaji Mechanical Engineer ISCO
What is the golden joint?
when there is restriction in the pipeline spool so that it can not be hydro tested (ex 1. The pipeline is hydro tested up to a pump inlet and the inlet joint is welded after hydro test. 2. the pipeline is getting connected to a header and the header gets connected to lot of branches where hydro test cant be done) the joints in the loop will be taken 100% radiography and all those joints are called as golden joints Balaji Mechanical Engineer ISCO
What is up stream pressure?
The upstream pressure is the pressure in a pipe or duct on the inlet side of a piece of mechanical equipment.
What is an inlet valve?
Inlet Valve is comprised of 2 words i.e. Inlet & Valve. Therefore Inlet Valve is that valve through which fuel or a mixture whose pressure in increased by reducing its volume in intaked into the cylinder.
Where is the ac low pressure side switch on 4.3 Blazer?
It's not a switch. The high pressure runs from the compressor outlet to the orifice tube inlet, and the low pressure side runs from the orifice tube outlet to the compressor inlet.
Where is the low pressure inlet located on a Ford Taurus?
on a 2005 ford Taurus the AC inlet is next to the firewall on the passenger side
What is manometric head?
it is the pressure difference between inlet and outlet of pump.
What is flash separation?
A flash separator consists of a vessel where the pressure is lower than the inlet stream. When the inlet stream enters the tank (which has a larger volume), the pressure may drop, as well as the temperature. When the pressure drops, the vapors dissolved in the liquid inlet will boil, "flash," into the vapor phase. Thus, the dissolved gases in the liquid are separated by "flashing" them.
What is mean flash separator?
A flash separator consists of a vessel where the pressure is lower than the inlet stream. When the inlet stream enters the tank (which has a larger volume), the pressure may drop, as well as the temperature. When the pressure drops, the vapors dissolved in the liquid inlet will boil, "flash," into the vapor phase. Thus, the dissolved gases in the liquid are separated by "flashing" them.
How do you control 1 bar air pressure in pipeline using pressure transmitter?
To maintain the pressure of 1 bar in a pipeline you would normally employ a regulator which has a diaphragm which works a needle valve balanced against an adjustable spring. An example of the use of a regulator would be the ones found on propane cylinders to regulate the gas pressure.
