0
What is the maximum overlap of steel rods in reinforced concrete sections?
Wiki User
∙ 14y ago
Steel reinforcing rods have minimum overlap requirements to ensure that the reinforcing has a continuous effect throughout the structure.
In some instances this minimum overlap is 600mm, but the requirement does vary and must be confirmed by an Engineer for each particular design.
Maximum overlaps would be used to ensure wastage is reduced, and to ensure adequate concrete cover.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the difference between lap splice length and development length for rebars?
The difference between the two is in the application. A development length is the amount of rebar length that is needed to be embedded or projected into concrete to create a desired bond strength between the two materials. The lap splice length is the length two rebar pieces must overlap and be tied together to create a bond as if there was no break and the run is "continuous". So simply put, development is rebar to concrete, splice is rebar to rebar. The lengths of both splice and development do vary. They are dependent upon different factors. These include but are not limited to concrete strength, rebar size, rebar coating and concrete cover or clearance. So when you see a chart on one project, it can differ from another for these reasons.
What is called degradation of signal over network cable?
It means that, as the signal travels over the wire, it will (a) get weaker, and (b) the signal for the individual bits will "spread out" until they overlap with the neighboring bits.It means that, as the signal travels over the wire, it will (a) get weaker, and (b) the signal for the individual bits will "spread out" until they overlap with the neighboring bits.It means that, as the signal travels over the wire, it will (a) get weaker, and (b) the signal for the individual bits will "spread out" until they overlap with the neighboring bits.It means that, as the signal travels over the wire, it will (a) get weaker, and (b) the signal for the individual bits will "spread out" until they overlap with the neighboring bits.
What is a Class A splice in concrete reinforcing?
A class A splice is defined in ACI 318 Section 12.15. There are two types of splice (A and B) which define the length of the splice as a multiple of the tensile development length (ld) Class A denotes a splice that has 1.0 x ld of overlap. A class B splice has 1.3 x ld. Class B is required except where splices are kept out of critical ares (see the code).
Why do only parts of the thread appear sharp and clear at any given time?
Because the thread overlap each other.
What is a teardrop in computer terms?
A DoS attack where fragmented packets are forged to overlap each other when the receiving host tries to reassemble them.
What is the purpose of the overlapping section in a Venn diagram?
The overlapping sections show elements that belong to each of the two (or maybe three) sets that overlap there.The overlapping sections show elements that belong to each of the two (or maybe three) sets that overlap there.The overlapping sections show elements that belong to each of the two (or maybe three) sets that overlap there.The overlapping sections show elements that belong to each of the two (or maybe three) sets that overlap there.
Which countries own which sections of Antarctica?
No country owns any section of Antarctica. Several countries, however, claim pie-shaped territories on the continent, some of which overlap. You can review the material below, to learn more.
How do you write overlap in the sentence?
I ama sitting overlap
What rocks and minerals are used to make concrete?
The stones in concrete are more correctly known as aggregate. They overlap each other from the top to the bottom of the pour, and this makes the curing and cured concrete much more resistant to cracking. The stones also give concrete a much higher compressive strength.
What leads to competitions between two species?
An overlap in their nichesAPEX 9.23.20
What is overlap repulsion in physics?
overlap repulsion in physics is repulsion overlapped
Climate zones and can overlap but they are not the same thing?
Biomes
What is overlap add and overlap save method in DSP?
example based on these method
What are food chains that overlap?
food chains that overlap I think are called overlapping food chains. Food chains that overlap are called overlapping food chains.
What extent morality and the criminal law overlap?
To what extent morality and criminal law overlap?
How many times do the hands of a clock overlap in 12 hours?
They overlap 11 times.
What is the typical allowance for overlap in draw draperies?
Add 4 inches to allow for overlap in the center.
