0
What is the minimum sample rate required to record a frequency of 96 kHz?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
A substance is the time required for half the atoms in a sample of a radioactive isotope to decay?
The time it takes for half the sample to decay is called the half-life.The time it takes for half the sample to decay is called the half-life.The time it takes for half the sample to decay is called the half-life.The time it takes for half the sample to decay is called the half-life.
The half-life of an isotope is the time required for half the nuclei in a sample to?
Half-life is the length of time required for half the atoms in a radioactive sample to decay to some other type of atom. It is a logarithmic process, i.e. in one half-life, there is half the sample left, in two half-lives there is one quarter the sample left, in three half-lives there is one eight left, etc. The equation is... AT = A0 2 (-T/H) ... where A is activity, T is time, and H is half-life.
What is a compressive force?
The force of compressing an object. A common example is a cement sample compression test. Cements best quality is its compressive strength. This is why it is used as a foundation for buildings. Anyways, the test is placing a cement cylinder at a certain size in a compression machine. It basically squeezes the cement or compresses the cement to the point of rupture. Then they record the amount a compressive force it took to rupture the cement sample. It has to meet a minimum standard to be accepted or they reject the product made from this batch. knowledgebasesoftware.wordpress.com/2011/10/14/knowledge-base-software-in-big-enterprises/
What is the bursting strength?
Bursting strength tells how much pressure paper can tolerate before rupture. It is important for bag paper.Bursting strength is measured as the maximum hydrostatic pressure required to rupture the sample by constantly increasing the pressure applied through a rubber diaphragm on 1.20 - inch diameter (30.5 mm) sample.
How does a grain moisture tester work?
Moisture meters use what is often referred to as the capacitive method or RF dielectric method. With this method a radio signal at a specified frequency is sent through the sample. As water interacts with radio waves (that's how your microwave oven works) it is possible to determine the moisture content by measuring how much the radio signal is changed by the sample. The effect that the sample has on the radio signal is termed the dielectric constant, and it increases proportionally to the moisture content. There are a number of other factors that have an effect on the dielectric constant, perhaps most notably sample density and temperature. These two factors are measured and corrected for in advanced moisture meters.
What is the minimum sample rate required to to record a frequency of 20 kHz?
According to the Nyquist theorem, a sample rate of double the frequency is required to record it, so 40 kHz .
What is the minimum sample rate for a signal frequency of 4kHz?
df
What happens if we sample the signal at sampling frequency nearer to signal frequency?
If you sample at more than the Nyquist frequency (one half the signal frequency) you introduce an aliasing distortion, seen as sub harmonics.
Relative frequency formula?
Probability of event = relative frequency = f/nf is the frequency of the event occurence in a sample of n observances.
Does the size of a sample affect the values of the frequency table?
Yes. If the sample is a random drawing from the population, then as the size increases, the relative frequency of each interval from the sample should be a better estimate of the relative frequency in the population. Now, in practical terms, increasing a small sample will have a larger effect than increasing a large sample. For example, increasing a sample from 10 to 100 will have a larger effect than increasing a sample from 1000 to 10,000. The one exception to this, that I can think of, is if the focus of the study is on a very rare occurrence.
What does the sampling theorem tell us concerning the rate or sampling required for an analog signal?
You must sample at 2 x the rate of the analog signal (2 x the analog signal frequency).
What does the term observed frequency refer to?
the frequencies found in the sample data
What is a part of a population callded?
Population is a noun.
How many alleles for black fur are in the sample population and what percentage of allele frequency does that reprent?
How many alleles for black fur are in the sample population and what percentage of allele frequency does that reprent?Read more: How_many_alleles_for_black_fur_are_in_the_sample_population_and_what_percentage_of_allele_frequency_does_that_reprent
Can a minimum data value of a sample be a negative number?
Yes.
What are the considerations for the choice of sample size?
Some considerations are:large samples take more time and money to processif the characteristic of interest is very variable then a large sample is required for accurate estimatesif the characteristic of interest is very rare in the population then a large sample is required to ensure that units with that characteristic are included in the samplethe greater the accuracy required of the estimates based on the sample, the larger the sample required.
What is the lowpass filter cutoff frequency that must be used to decimate to reduce the sampling rate from 8kHz to 4kHz?
2kHz - That's the nyquist frequency at a sample frequency of 4kHz.
