0
What else can I help you with?
When a parallel LC circuit is tuned to resonance will the current be at a maximum or a minimum?
Inside the circuit loop between the inductor and capacitor the current will be at maximum. Outside the circuit the current through the LC tank circuit will be at minimum. It depends on where you are measuring it.
How a circuit breaker increases safety?
A circuit breaker limits the amps that a circuit can carry. If the amperage draw on a circuit exceeds that limit, the circuit breaker turns off the circuit. If the current through a wire exceeds the rated amperage, the wire will overheat and eventually cause a fire, or at a minimum, destroy the wire behind inside the wall. Obviously, people don't want a house fire caused by an electrical overload, so circuit breakers are used to prevent damage and potential loss of life.
How do you know if the AC breaker matches the AC unit starting demand load?
Read the literature for the ac condensing unit, or the tag on the outside of the unit. Minimum circuit ampacity= minimum breaker, wire and fuse size. Maximum circuit ampacity= the maximum size. Your circuit breaker, wire size and disconnect fuses should all be at or between those 2 numbers.
What is the minimum Earth fault current that an Earth leakage protection unit must be able to sense?
10mA
When the circuit is said to be in resonance?
For a particular frequency if the current or the voltage of the circuit is Maximum or Minimum then that circuit is said to be in resonance .
How do you find the current rating of a circuit breaker?
A circuit breaker, like a switch, turns power on and off by moving one conductor to touch or not touch another conductor. The gap when not touching has to be large enough that electrons cannot pass through the air to the other conductor, producing a spark. The larger the voltage, the farther it can pass through the air, and the larger the gap must be. So the rated voltage of a circuit breaker or a fuse is the largest voltage it can safely control.
Why parallel circuit is known as current magnification though it has minimum current at the time of resonance?
In a parallel circuit, each branch has its own current path, allowing the total current to be the sum of the currents in each branch. This is why it is known as current magnification. However, at resonance, the impedance in the circuit is at its minimum, causing the total current in the circuit to decrease. This does not change the fact that individual branches can still have higher currents than in a series circuit due to the unique current paths in a parallel arrangement.
How does a circuit breaker protect you?
A circuit breaker limits the amps that a circuit can carry. If the amperage draw on a circuit exceeds that limit, the circuit breaker turns off the circuit. If the current through a wire exceeds the rated amperage, the wire will overheat and eventually cause a fire, or at a minimum, destroy the wire behind inside the wall. Obviously, people don't want a house fire caused by an electrical overload, so circuit breakers are used to prevent damage and potential loss of life.
What are the three main types of high voltage switching gear met with in industrial installations?
High voltage switch gear operates in the voltage range of 36 kV and above. Minimum oil circuit breaker, air blast circuit breaker and SF6 (Sulphur hexafluoride) circuit breaker are the three mostly used disconnects for high voltage switchgear.
Is it legal under NEC to extend a 480 volt 3 phase 20 amp circuit with different size conductors for L1 L2 and L3 as long as the gauge meets the circuits ampacity requirements?
I assume your sizing the 20 amp from the breaker? NEC 240.3 states minimum conductor size for the rated ampacity of the circuit breaker. In this case, minimum size for 20 amp breaker is 12 AWG. I assume you are wiring a motor? I suggest you size your over current in accordance with NEC, start reading around NEC 430.
What is the minimum fuse rating is needed for a 12 volt circuit?
No current bro? Depends
What is the minnimum size equipment grounding conductor required by the NEC for a branch-circuit protected by a 50-ampere rated circuit breaker?
The minimum size equipment grounding conductor required by the NEC for a branch circuit protected by a 50-ampere rated circuit breaker is 10 AWG copper or 8 AWG aluminum.
