0
What is the name of the process used to connect electrical components to a circuit board?
Wiki User
∙ 10y ago
The process of connecting electrical components to a circuit board is
known as glueing, cementing, strapping, or bolting.
The process of connecting components electrically to points in the circuit is
known as soldering.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is the meaning of electrical components?
Electronic component are those component which are used to make the electronic circuit it may be active or passive . some active components are - Diode ,FET,BJT,MOSFET, and HEMT etc. while passive component are those device which can not process/amplify signal like- resistor capacitor inductor etc.
When was the integrated circuit made?
1958, but the germanium based process was difficult and expensive to use, requiring all the components in the IC be interconnected by hand under a microscope. It took another year or so for the silicon based planar process to be used, which allowed all components and interconnects to be made using photolithography.
What an electrical cell is and how it causes a current in an external circuit?
An electrical cell is the basic unit from which electrical batteries are made. The cell is composed of two plates made of different conductive materials and a liquid electrolyte (in "dry" cells this liquid is in the form of a moist paste). Electric charge is produced between the two plates by the electrolyte interacting with and causing corrosion of one or both plates. Once the electric charge is produced the corrosion process slows or stops, unless an external circuit is connected between the plates. When an external circuit is connected between the plates, current flows through that circuit and the electric charge is slightly reduced. The corrosion process continues at a rate necessary to maintain the electric charge, until the chemicals in the cell are used up.
What is the process of circuit design?
The circuit design process covers systems ranging from highly complex to simple. The design process for simple circuits can usually be completed by one person, while teams of designers may be required to complete the process for more complex circuits.
What property of the materials used in computer chips makes them useful as switches that turn electric current on and off?
They are semiconductors and their electrical properties can be very precisely controlled by adding dopant impurities to create a wide variety of components integrated into one chip. Transistors of various types created by this doping process can act as switches or amplifiers depending on the other components integrated around them and connected to them.
What is the meant by the following term Assembly process?
The term 'Assembly Process' is when you build and put together all the parts to create something, for example: 'The assembly process of a computer would be to connect all the electrical components together to make it work.'
What is a printed circuit board?
A printed circuit board is basically used to mechanically support while at the same time electrically connecting electronic components by using conductive pathways. The process is very simple.motherboard is a printed circuit ,where all components of the system is connected.Printed circuit boards are used in nearly all electronic devices.The conducting wires that connect all the components, are printed onto an insulating plastic material such as paxolin or fiberglass. These tracks are commonly made of thin copper sheet stuck to the board. The tracks are then printed using light and a chemical process to remove the unwanted copper.Some boards used in remote controls and wafer thin boards used in ipods etc, are commonly printed, using conductive ink containing silver or carbon.The alternative to printed circuits was to idividually wire the coponents using wire and solder tags. Old tube radios were originally wired this way, but had to be made by hand.Printed circuits allow for automation and mass soldering using a float soldering process on a bed of molten solder.
What is the meaning of electrical components?
Electronic component are those component which are used to make the electronic circuit it may be active or passive . some active components are - Diode ,FET,BJT,MOSFET, and HEMT etc. while passive component are those device which can not process/amplify signal like- resistor capacitor inductor etc.
What kind of electrical circuit can sense an electrical signal process it and give an electrical output?
Automatic garage door opener with a remote The answer above will give a mechanical output not an electrical output. Photocells come to mind.
How can electrical testing meters aid in the troubleshooting process of an appliance?
Electrical testing meters can definitely aid in the troubleshooting process of an appliance. This is because if it reads "no voltage" when plugged into the outlet, then the fuse or circuit is at fault, not the appliance.
Can you use electrostatic paint over a painted metal surface?
No. The electrostatic process requires a electrical circuit to be made which will not happen on a painted surface.
Does a refrigerator have transistors?
A fridge may or may not have a few transistors in it, these are electrical components that would probably be part of the control circuitry. Transistors used to be very common components of most electrical appliances. The cooling process of the fridge has nothing to do with transistors and is handled by a compressor and a heat exchange pump
What does it mean for an electrical circuit to have a short?
Shorts are usually a style of clothing that prevents one from exposing private areas otherwise unacceptable in a public setting. Electric shorts look much better when put on gradually or slowly. Another interpretation comes from short meaning small. When a circuit is in the beginning process, it is considered to be an "Electrical short circuit".
What is the process taking place in a battery?
The electrical pressure is created inside a battery and it provide the voltage which creates orr pushes current to flow in the circuit.
Why doesn't a nail in an electrical circuit rust?
The rusting of a nail (iron) is an oxidation process. An iron nail in an electric circuit has a much higher potential difference than its oxidation potential, so it cannot oxidize.
The components that process data in a computer are where?
The components that process data are located in the system unit
Do charges in an electric circuit flow because of a difference in electrical potential energy?
"voltage" (also referred to as 'potential')
