0
The output voltage of a digital receiver will vary depending on the design and manufacture of the particular receiver, and the output system used. It is normally quite low, typically between 1 and 5 volts, ranging up to 12 for some SCART connections.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Difference between linear IC and Digital IC?
In linear IC'S the output voltage is very according to input voltage In digital IC's the output voltage is either high or low
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
Why is the voltage reading always a minus figure when using a digital multimeter to measure the DC voltage from the output jacks of a cassette deck?
I would imagine that reversing the leads would rectify that. (No pun intended.)
What determines the output voltage and the current of a transformer?
The ratio of output windings to input windings determines the ratio of output voltage to input voltage. The ratio of current is the inverse.
Why might the unloaded output voltage of a transformer be higher than its rms of 12.6v?
Because the windings of transformers have resistance, the primary and secondary currents will cause voltage drops. To compensate for the drops, the transformer may have been designed to have a higher than specified output voltage when there is little or no output current. The no load output voltage typically is only slightly greater than the specified voltage. Before measuring the output voltage, measure the input (line) voltage. If it is not as specified for the transformer, calculate its effect on the output.
Does skybox has digital audio output?
Some models of Skybox receivers have a digital output. You'll have to check the back of the box to see.
Difference between linear IC and Digital IC?
In linear IC'S the output voltage is very according to input voltage In digital IC's the output voltage is either high or low
Do they make a digital audio cable that fits older receivers?
It's not as simple as making a cable that fits. Digital audio cables and digital signals, both coaxial and optical, require a digital input. You need to convert the digital signal to analog to work with older receivers. These are available (Google Digital to Analog Converter or DA Converter). Just about every device that has a digital output will also have an analog stereo output, which will work with your old gear.
What year are you swiching to digital cable?
Most cable companies have had digital cable and receivers for a few years now. It's the box attached to it that determines if you have a digital output for a newer digital TV available or not. Satellite has been digital all along, but the same situation applies in that the receiver determines if you have a digital output available.
What voltage is a western digital 4008A external hard drive?
12V DC & 2A output
What is the Difference between linear IC and digital IC?
Both linear ICs and nonlinear ICs has an output voltage which is dependent on the input voltage. However, the difference is that linear ICs produce an output voltage which increases or decreases at a "fixed rate" relative to the input voltage. Nonlinear ICs do not do this. A voltage regulator may be considered nonlinear because as you increase the input voltage the output will climb at the same rate (just like linear ICs), however, once the input voltage reaches a particular level point, the output no longer increases as you increase the input. This is at the point where regulation begins. The nonlinear IC no longer changes its output at a fixed rate relative to the input.
Can a digital circuit produce the same output voltage for different input voltage values explain?
No, value of output voltage depends upon the value of input voltage and digital can not produce the same output voltage for different input values. For example, suppose in a digital circuit two switches are connected. A closed switch is represented by 1 and an open one by 0. If there are two switches and we say that they are in state 1, then it would mean that both of them are closed. In this circuit after connection with the battery some current would pass so we call this current as output.Depending upon the states of the switches, the current either would pass or it would not pass.In case the current is passing, we can say the value of output is 1 and it is 0 when no current is passing. Whether the value of the output would be 1 or 0, it depends upon the values of input variables( 1 and 0) which specify the state of the switches.In this example, the switches form the input variable because the value of output depends upon the state of these variables which shows that digital circuit can not produce same output voltage for different values of input voltage.
What does the company Sonicview make?
The company Sonicview manufactures products for television viewing such as satellite receivers, wireless receivers, cable receivers, and Dolby digital receivers.
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
Where can one find more information about digital receivers?
There are many companies and websites that have a host of information available on digital receivers. Some of these websites with digital receiver information are Best Buy and Radio Shack.
Is it the value of input voltage equal the value of output voltage?
No. There are several factors that may affect the output voltage. For instance: Resistors, Transformer, Voltage regulators and others that can control the output voltage to a certain level.
How does an alternator know how much voltage output?
Output of the alternator is controlled by the voltage regulator.
