0
What is the preferred place to hook an RV into a 1995 Saturn SW-2 wiring harness?
Brad5131
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace a wiring harness on a Dodge Ram?
The wiring harness can be removed by unplugging all of the wires. The wiring harness is also held in place by several retaining screws. Remove the retaining screws.
Where can you get a engine wiring harness for a 1988 Nissan Pulsar NX?
The best place is to get it from a wrecking yard.
Where can one find a wiring harness?
Wiring harnesses are often very job specific, if one is after a harness to repair or modify an existing appliance or other product (e.g. car) the best place to look is at the manufacturer. If looking for a generic wiring harness to make one's own wiring, electrical or hardware stores are the best bet (e.g. Jaycar, Masters, etc.)
How do you take off engine wiring harness from a 91 Toyota cressida?
There are six steps on how to take off the engine wiring harness on a 91 Toyota Cressida. Some of the step-by-step instructions are disconnect and remove the battery, remove the old harness, and use a small screwdriver to remove the clips and retainers that hold the harness in place.
How do you change a wiper motor in a 89 Chevy truck?
remove wiring harness, remove nuts, place new one (or rebuilt one) on, replace nuts, plug in harness.
Where is the crankshaft position sensor on a 1993 jeep wrangler?
its on the bottom. near the bell housing for the tranny. its held in place by a screw on both sides. it will also have a small wiring harness. its on the bottom. near the bell housing for the tranny. its held in place by a screw on both sides. it will also have a small wiring harness.
Where is the radio harness that you can hook your aftermarket radio into?
Usually when you get the radio the place you bought it will have a wiring harness that will fit the car. If not then go to a radio installation shop and ask for one. This will then plug right into the factory car harness and then you connect the radio to this harness. That's it. Good luck.
Where is the blower motor resistor on the Xterra?
just behind the blower motor under the passenger side dash is a plug (with a large white plastic wiring connector) that is the resistor. two screws (7/32?) hold it in place as well as a small spring clip holding the wiring in place. just remove the two screws and pull out. To remove the resistor block from the wiring harness, squeeze in on the two tabs at the wiring end of the white harness. xterraparts.com has them for about $19.
How do you change a headlight in a 2001 Toyota landcruiser?
The headlights on a 2001 Toyota Landcruiser are changed by opening the hood, disconnecting the wiring harness to the lights, and twisting the bulb. A new bulb can then be put in place and the harness reattached.
Coolant sensor on a 1998 Saturn?
Easy place, just hard to describe. It is located on the side of the engine, not front or back. It is located on the drivers side. A little below and back of the the upper radiator hose. (I RECOMMEND WHEN REPLACING THE SENSOR, TO ALSO REPLACE THE WIRING FOR IT TOO, GM SELLS THE NEW HARNESS FOR IT).
How do you install a new stereo in a 1993 Mercury Topaz?
all you have to do to get out the old one is there is a hole on bolth sides of the stero and if you get a hanger it will normally work and you just have to pull it out i thought i was going to break some thing but it was all good
How do you hook up trailer wiring on a Pontiac Montana?
I bought a wiring harness at a store specializing in all things trailers for my 2000 Montana (they are also readily available on-line). The instructions were so-so, but what you need to find is the place behind the cover in driver side trunck. On mine, there was a plug to accept the wiring harness. After that it just about routing the wiring - I routed mine through the rubber grommet where the brake light goes.
