Happened to me, I went out and bought a lotto ticket. High beams work so I just assume dumb luck.
It is dependant on whether the switches are in wired in a parallel or series configuration. If the switches are wires in parallel then both switches would have to be off to turn the light bulb off. Either switch could turn the light bulb on. If the switches are wired in series then both switches would have to be on to turn the light bulb on. Either switch could turn the light bulb off.
Yes you can. There are three ways of doing this. Two are incorrect and one is the correct way of doing it.The two switches can be paralleled together to make the light fixture respond. Both of the two switches will always have to be in the on position. Either switch will turn the light off but the second switch will not turn the light on. Very inconvenient when you enter a room through one door and leave by another.The two switches can be wired in series. Both switches have to be on to operate the light but again if one of either switch is left in the off position the other switch will not operate the light fixture. Very inconvenient when you enter a room through one door and leave by another.The correct way of wiring two switches to control a central light fixture is with a three way switching system (two way in the UK). The two positions have to have special three way switches in each position. These types of switches sort out the problems of leaving a switch in a certain position to operate properly. The only criteria is that there be a three conductor cable joining the two three way switch boxes together.See related links below.
Yes. the two switches are called '3-way' switches. You will have to turn the fan/light on with one of the switches and leave BOTH switches in that position. The remote control unit will have to be wired in between the switch that is supplying power to the devices and the devices. This is the simplest way. You could also disable one of the switches and replace the remaining switch with the RC unit. If you are not sure how to deal with 3-way switches, learn about them first, or call a good electrician to do all of the work. Remeber that the black wire is hot, but only if the house was wired properly in the first place.
No, Mexico and Greece are both separate countries.No, Mexico and Greece are both separate countries.No, Mexico and Greece are both separate countries.No, Mexico and Greece are both separate countries.No, Mexico and Greece are both separate countries.No, Mexico and Greece are both separate countries.
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
The single light will not come on. The traveler legs from the two switches will have to be opened simultaneously if they are not then you will get a flick of light.
It is dependant on whether the switches are in wired in a parallel or series configuration. If the switches are wires in parallel then both switches would have to be off to turn the light bulb off. Either switch could turn the light bulb on. If the switches are wired in series then both switches would have to be on to turn the light bulb on. Either switch could turn the light bulb off.
Price
Send power to the 1st switch and then send the power from that switch when it is in the on position to the second switch. Then send power to the light from the second switch. That way both switches will have to be in the on position for the light to be on.
Yes, both can work from the same set of switches.
They are both measures of probability.
are they dependent or independent? define success and failure for the 2 events. probability of success (EX: drawing a face card) = number of possible successes / total possible events. Multiply the two separate probabilities to get the probability that both occur.
If these conditions both occurred at the same time it may indicate a body control module problem. They can also be separate circuit issues as in bad bulbs and inoperable door switches/actuators.
Yes you can. There are three ways of doing this. Two are incorrect and one is the correct way of doing it.The two switches can be paralleled together to make the light fixture respond. Both of the two switches will always have to be in the on position. Either switch will turn the light off but the second switch will not turn the light on. Very inconvenient when you enter a room through one door and leave by another.The two switches can be wired in series. Both switches have to be on to operate the light but again if one of either switch is left in the off position the other switch will not operate the light fixture. Very inconvenient when you enter a room through one door and leave by another.The correct way of wiring two switches to control a central light fixture is with a three way switching system (two way in the UK). The two positions have to have special three way switches in each position. These types of switches sort out the problems of leaving a switch in a certain position to operate properly. The only criteria is that there be a three conductor cable joining the two three way switch boxes together.See related links below.
What you are talking about is a three way switching system. There are many diagrams for this type of connections on the net. If you install two light switches in parallel both switches would have to be in the off position for the light to go out. Check out the design of a three way switch this is what you need.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS
That probability is the product of the probabilities of the two individual events; for example, if event A has a probability of 50% and event B has a probability of 10%, the probability that both events will happen is 50% x 10% = 5%.
The probability that he will not win both games is 0.58