The VA of the transformer is the product of the amps x the volts. V x A = Watts. 50kVa is equal to 50,000 watts. It holds true on the primary and the secondary. The formula to use is I = W/E. Amperage = Watts (V x A)/volts.
AnswerThe above answer will determine the rated currents of the primary/secondary windings. But the actual currents (which shouldn't exceed their rated values for any length of time) are determined by the load. For example, with no load, no secondary current will be flowing, and the primary current will be reduced to its magnetising current value.
Transformers are rated in KVA, both the primary and secondary windings have the same KVA rating. (KVA is the voltage multiplied by the amperage then divided by 1000). If you have a 10 KVA step up transformer with 120V on the primary: A = 10k / 120 = 83.33A and if the secondary produces 240V: A = 10k / 240 = 41.667A
Divide the LEDs current into the voltage and derive a proper current limiting resistor value. 16/0.02=800 ohms. That is for a 20 ma LED.
All transformers are designed to work on AC. They do not work on DC.If you connect an inductor to DC, the current will increase until the capacity of the source or the conductance (1/resistance) capacity of the inductor and conductors is reached. Often, this condition will overheat and destroy the inductor, or destroy the source. A transformer is not an exception, as it is a form of inductor.
Depends on what the voltage is being stepped down in that particular control transformer. Control transformers usually step down a voltage of 480/208v to 120V. The 120Volts can now be used in safer manner to "control" start/stop buttons, and other components that are only built to run on 120V
You can get a transformer that converts the UK's 230V power to 120V, but you cannot get a transformer that will convert from 50Hz to 60Hz. Often, US equipment can work, except that they will work hotter and less efficiently on the 50Hz power. Consult your clipper and trimmer documentation - you may find that it will work just fine on 50Hz.
The kVA rating will be listed on the transformer's nameplate, which is usually on the front of the transformer. The 480v to 120v is irrelevant, because many transformers with different kVA ratings convert 480 volts to 120 volts. The kVA ratings can be different and thus affect the rated current through the transformer.
You can buy a transformer that will output 12 volts DC at just about any electronics or department store. You will need to check the amperage as well to make sure that the transformer can handle the current draw, but for a radio this should not be that high (it's okay for the transformer to be rated for MORE amps than the radio draws).
This type of a transformer is known as a step up transformer.
Use a step down transformer 240 primary to 120 secondary. You must know what the connected load (amps) is so that you don't overload the transformer. Small transformers are rated in VA.
Transformers are rated in KVA, both the primary and secondary windings have the same KVA rating. (KVA is the voltage multiplied by the amperage then divided by 1000). If you have a 10 KVA step up transformer with 120V on the primary: A = 10k / 120 = 83.33A and if the secondary produces 240V: A = 10k / 240 = 41.667A
No. The neon sign is fed by a step-up transformer. Primary side 120V, secondary side 7500V. If you applied 240 to the primary side you would get 15000 volts on the neon tube. A flash over and then nothing. If you can find a transformer from 120V to 240V or 240V to 120V then you are good to go. Connect 240V to 240V side and you will get 120V out the other, connect the 120V side to the neon sign and you should have light. Transformer should be at least 100va. This will give you an output of .83 amps at 120V
4160/120 = 34.666666 to 1
Divide the LEDs current into the voltage and derive a proper current limiting resistor value. 16/0.02=800 ohms. That is for a 20 ma LED.
Please go to discuss question page.
the simplest solution is by connecting two 120v 3amps heater in series , the same can be used directly on 240v. However the current drawn will still be 3 amps & Not 1.5 amps. The heater output power will be double that of a single heater running on 120v. ( or equvalent to two heaters operating on 120v. supply ) A more expensive method is to use a stepdown transformer which can be powered on 240v & connect the heater on the transformer 120v side. this method will consume approx. 1.5 amps from the 240v supply.
120V appliance will not work on 220V. Use an instrument transformer or voltage regulator to adjust the high voltage to the desired level.
All transformers are designed to work on AC. They do not work on DC.If you connect an inductor to DC, the current will increase until the capacity of the source or the conductance (1/resistance) capacity of the inductor and conductors is reached. Often, this condition will overheat and destroy the inductor, or destroy the source. A transformer is not an exception, as it is a form of inductor.