4160/120 = 34.666666 to 1
Off hand no but your explanations are not clear as to who is doing what to whom,,
Yes, you can obtain 120V single-phase power from a 440V three-phase system using a transformer. By using a step-down transformer that reduces the voltage from 440V to 120V, you can safely access single-phase power. It's important to ensure that the transformer is correctly rated for the load and that all safety regulations are followed during installation. Always consult with a qualified electrician for any electrical work.
To step up a 40-volt output to 120 volts, you would typically use a transformer designed for voltage increase, known as a step-up transformer. The transformer must have a turns ratio that corresponds to the desired voltage increase; in this case, the ratio must be 3:1 (120V/40V). Alternatively, you could use a DC-DC converter if the voltage is DC, which can also boost the voltage to the desired level. Always ensure that the components used can handle the power requirements safely.
A 24v transformer converts 120v to a lower voltage for use in push buttons, like doorbells, thermostats, gas valves, or air conditioning systems. They are an essential tool for electricians.
Not directly, you would need to transform 480v circuit to 120v with a transformer first.
Count the turns ratio of the windings. The voltage ratio is equal to the turns ratio. The current ratio is equal to the inverse of the turns ratio. For instance, a power transformer with a 10:1 turn ratio (primary to secondary) running on 120V will produce 12V. If it consumes 1 ampere from the input, it will provide 10 amperes to the output.
This type of a transformer is known as a step up transformer.
The ratio of AC voltages is the same as the ratio of winding-turns in the transformer. Vp / Vs = Np / Ns (10 volts AC) / Vs = 200 / 20 = 10 Vs = (10 volts AC) / 10 = 1 volt AC.
You can use a step-up transformer. Transformers are rated in primary voltage, secondary voltage, kVA, phases (single and three) and other parameters then equipped with indoor and outdoor enclosures. Be sure to consult a professional engineer or electrician when choosing and installing a step-up transformer. There are several NEC issues involved as well as choosing a transformer that is right for the type of load you have. One without the proper licensing AND knowledge of transformer circuits should never install 480V wiring or transformers.
To determine the output current in amps for a 0.50 kVA transformer with a 277V input and 120V output, you can use the formula: Power (kVA) = Voltage (V) × Current (A) / 1000. For the output at 120V, the current would be calculated as follows: 0.50 kVA = 120V × Current (A) / 1000, which gives Current = (0.50 × 1000) / 120 ≈ 4.17 amps. Thus, the transformer can provide approximately 4.17 amps at the 120V output.
120v
Please go to discuss question page.
120V appliance will not work on 220V. Use an instrument transformer or voltage regulator to adjust the high voltage to the desired level.
Yes, you can obtain 120V from a 380V three-phase system using a transformer. By utilizing a step-down transformer designed to convert 380V to 120V, you can safely provide the desired voltage for single-phase loads. Additionally, you can also achieve 120V by using a phase-to-phase connection in a three-phase system, depending on the system configuration. However, it’s crucial to ensure that the transformer and wiring are properly rated for the application to ensure safety and efficiency.
No. The neon sign is fed by a step-up transformer. Primary side 120V, secondary side 7500V. If you applied 240 to the primary side you would get 15000 volts on the neon tube. A flash over and then nothing. If you can find a transformer from 120V to 240V or 240V to 120V then you are good to go. Connect 240V to 240V side and you will get 120V out the other, connect the 120V side to the neon sign and you should have light. Transformer should be at least 100va. This will give you an output of .83 amps at 120V
Off hand no but your explanations are not clear as to who is doing what to whom,,
You can use a transformer or voltage converter to step up the voltage from 120V to 205V for your equipment. Make sure to select a transformer that can handle the wattage and current requirements of your equipment to avoid damaging it.