0
What is the reason for measuring the bearing of survey lines in a compass traversing at both ends?
Wiki User
∙ 8y ago
It is to alert the surveyors to any magnetic anomaly that may affect one of the ends. The anomaly would arise because of geological features.
Wiki User
∙ 7y ago
Measuring the bearing of survey lines at both ends ensures accuracy and reliability in determining the direction of the survey line. This helps in verifying and adjusting for any errors that may have occurred during the surveying process, ultimately leading to more precise results for mapping and construction purposes.
Add your answer:
Earn +20 pts
What are the sources of errors in compass survey?
Sources of errors in compass surveys include magnetic declination errors, local magnetic disturbances, poor compass calibration, incorrect reading of the compass, and human error in taking and recording measurements.
Why is the logo of Freemasonry and Iglesia ni Cristo similar?
The logos of Freemasonry and Iglesia ni Cristo both feature a square and a compass. While they appear similar, they have different symbolic meanings in each organization. The square and compass represent different values and principles within Freemasonry and Iglesia ni Cristo.
Which was not a reason for the growth of suburbs?
One reason for the growth of suburbs was increased automobile ownership and improved transportation infrastructure.
How does imagination overcome reason?
Imagination can override reason by allowing for creative thinking and exploring possibilities outside the constraints of logic. When imagination takes over, people may come up with innovative solutions or ideas that challenge traditional ways of thinking. However, it's important to strike a balance between imagination and reason to ensure practicality and feasibility.
What is the primary reason for the differences people have in behavior and attitude?
The primary reason for differences in behavior and attitude among people is their unique combination of genetics, upbringing, experiences, and environment. These factors shape individuals' personalities, beliefs, and values, influencing how they interact with the world around them.
Keuffel and Esser contractor's compass Why are E and W transposed?
The reason for this is that it is a surveyor's compass with fixed sites along the north south axis and this allows easy non reversed readings of bearings. When you turn the compass siting on this axis the needle of course follows magnetic north. Align the sights with magnetic north and then turn the compass clockwise 45 degrees which should be North East or N 45 degrees E and you will see that the needle is showing the correct bearing because the East and West are reversed. Ken S.
Why the compass shows north in Telugu?
same reason it shows North anywhere. The needle of a compass is a magnet. It points to the North Magnetic Pole.
What scientific reason is there for measuring air pressure?
loop is funny
What is a reason to use a compass rather than a GPS?
To navigate your way if your in the middle of nowhere.
What happens when you overheat a bearing?
When a mechanical bearing becomes overheated for whatever reason, the lubricating material will become less viscous, and the danger of metal-to-metal contact increases. This will lead to the failure of the bearing.
Can you put a used piston in car?
There is no reason why you can't. If the rod bearing is still in it, you can tell if it has been spun. If the bearing appears alright, there should be no reason to have it checked. You would use new rings and a new bearing which are the parts that matter. You might even be able to use the old rings and bearing, but no one would. Too much chance of having a problem after it was put in.
How can you measure bearing?
It depends on the type of bearing, and which measurement. A double race roller bearing is measured on the inside (shaft diameter) with an internal vernier caliper or similar device. On the outside (casing or pillow block diameter) with an external vernier. And the width (or length) of each race can be measured with and external vernier. A babbitt bearing can be measured by measuring the journal on which it is to be mounted, then taking "leads" (or using plastigages), by placing lead fuse wire or a plastigage on the journal, placing the bearing top half over the leads, and bolting down the bearing housing over that. Then unbolt the bearing housing remove the top half the bearing and with a micrometer measure the crushed thickness of the fuse wire. Add this to the journal diameter to get the internal diameter of the bearing. The main reason for taking leads is to determine the oil wedge gap in the bearing to see if it is the right thickness. If it is too thin the bearing needs to be scraped if it is too thick the bearing needs to be replaced or the journal built back up to the correct diameter.
What is stronger hip or shoulder joint why?
In humans, the Hip. The reason because it is weight bearing.
Can you tow a 2007 Jeep compass 5 speed manual transmission 4 wheels on ground?
Hi, Thank you Rdrsh for your answer, any REASON why you cannot flat tow a MANUAL Jeep Compass 2007 ??
What the reason of kw and amps mismatch?
its the operating power factor & bearing conditions(rotary equipments)
Are the units of volume cubed or squared why?
Cubed. The reason is that space has three dimensions - and that is basically what we are measuring.
How will humans survive without measuring tools?
We humans do still have measuring tools, so I am not sure why this question comes up, but if for some reason we were to lose all of our measuring tools, then we would just have to make estimates. Or create new tools.
