0
What is the reason of reverse indication on in single phase kWH meter?
Wiki User
∙ 10y ago
A kWh meter measures the flow of energy along the circuit that the meter is connected to. Normally power flows from the supply to the load, which is the conventional direction, but in some cases, for example if the load is replaced by a generator, power can flow the other way and in that case the meter indicates a backward, negative, flow of power.
Wiki User
∙ 10y ago
Wiki User
∙ 8y agoWhy would you want to do this except for trying to steal power from the utility company. You will get no help here with your thievery.
Add your answer:
Earn +20 pts
Why three phase meter is better than single phase meter?
A three-phase meter can be used for single phase while the reverse is not the case.
Reverse running of three phase meter?
The reverse running of a three phase meter is possible when one of the meter's two potential coils fails. This is a problem found typically on a Delta service. A three phase meter in this condition is damaged and will report lower energy use than actual.
What possible damage can analog meter suffer if the polarity connections are reversed?
It shows reverse readings
What is the difference between single phase and three phase voltage measurement?
Phasing, or the number of phases in an electrical system has nothing to do with the voltage. A single phase and three phase supply could have a voltage supply of any given voltage from virtually 0 to infinity. Most single phase power supplies in the US are 120/208-240 volt. Three phase power supplies are typically 120/208 to 277/480 volt.
How do you measure amps on a 208V single phase circuit with a clamp on amp meter?
Clamp the meter around the energized conductor that is connected to the load to be measured and read the amperage off of the dial face of the meter.
Why three phase meter is better than single phase meter?
A three-phase meter can be used for single phase while the reverse is not the case.
Reverse running of three phase meter?
The reverse running of a three phase meter is possible when one of the meter's two potential coils fails. This is a problem found typically on a Delta service. A three phase meter in this condition is damaged and will report lower energy use than actual.
In poetry the words anapest and iamb are used to describe?
Different kinds of feet in classic scansion. Typically there is an indication of the kind of foot in a typical line, along with an indication of the number of those feet per line, as in 'iambic pentameter'.
What is meaning of stop mode in TOD energy meter how can reverse energy calculated in TOD meter?
WikiAnswers does not give information about illegal acts, such as tampering with with a TOD meter.
If you reverse the flow on a water meter will it turn the meter backwards?
Yes, a water meter will run backwards. Running your meter backwards is stealing and could result in your service being diconnected and or a fine. Modern meters that are read via radio signals are sofisticated electronic instruments and will report leaks and reverse flows when read. So if your meter is a radio read type you had better not mess with it.
What is the reason for headless angel statues?
a meter!!!
What is the meaning of the root word meter?
The root word "meter" refers to measurement or something that measures. It is commonly used in words related to measuring length, such as thermometer or barometer.
Can watt meter negative reading?
Yes. This is usually an indication that either its current coil or its voltage coil has been wired incorrectly.
What possible damage can analog meter suffer if the polarity connections are reversed?
It shows reverse readings
How long is a square meter?
A square meter is a unit of area, not length. You cannot say how long it is. As an area, it is a square with sides of length 1 meter. If you want an example: a single bed is about 1m x 2m, so a square meter is about half the size of a single bed.
How do you test a single phase transformer?
with an meg ohm meter
What is the difference between single phase and three phase voltage measurement?
Phasing, or the number of phases in an electrical system has nothing to do with the voltage. A single phase and three phase supply could have a voltage supply of any given voltage from virtually 0 to infinity. Most single phase power supplies in the US are 120/208-240 volt. Three phase power supplies are typically 120/208 to 277/480 volt.
