0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where is the RKE Remote Keyless Entry module located on a 1998 Chevy Corvette?
== ==
Where is the rke entry module located on a dodge neon 2005?
It is located under the dash panel in the front middle in a black box.
Where is the rke module on a 97 Saturn?
passenger side back seat, behind the panel by the door. may have to remove floor panel and/or seat.
Where is the control module on a 1995 chrysler Concorde?
Engine, transmission, ABS are under the hood. Body, airbag, cluster, HVAC, RKE, are inside the dash.
1998 dodge ram 1500 program remote key fob?
To program the Remote Keyless Entry (RKE ) transmitter access codes into the RKE receiver in the Central Timer Module (CTM ) requires the use of a DRB scan tool. SYSTEM OPERATION The Remote Keyless Entry (RKE) receiver is a radio frequency unit that is integral to the high-line version of the Central Timer Module (CTM). The CTM also contains the program logic and control circuitry for the RKE system. The CTM is mounted under the driver side end of the instrument panel, inboard of the instrument panel steering column opening. The RKE receiver has a memory function to retain the vehicle access codes of at least one, but no more than four RKE transmitters. The receiver is designed to retain the transmitter codes in memory, even if the battery is disconnected. The RKE receiver is energized by one of three radio frequency inputs from the RKE transmitter; Unlock, Lock, or Panic. The programming of the CTM responds to these RKE inputs, as well as many other inputs, by sending the proper control outputs to the power lock motors, the courtesy lamp circuit, the horn relay, and the headlamp (or security) relay. For diagnosis or programming of the RKE receiver within the high-line CTM, a DRB scan tool and the proper Diagnostic Procedures are recommended. The RKE receiver is only serviced as a unit with the high-line CTM and, if faulty or damaged, the CTM unit must be replaced
Where is the reset button on the RKE Module on a 2004 Kia Optima?
You may not need the reset button. Try disconnecting the negative battery terminal for a period of time, possibly up to 30 minutes. The RKE system on our Kia Optima often stops working, and unhooking the power makes it work again.
How does a horn get stuck on in a 1996 Saturn SL2?
Three usual suspects: #1 the switch contacts in the steering wheel can wear and get stuck together, or the wire running through the switches, roll connector (connects the part of the steering wheel that turns to the rest of the car that doesn't) to horn gets frayed and grounded or #2 the remote keyless entry (RKE) module is defective or #3 the wire from the RKE module to the horn module has frayed and grounded. Anything that grounds the "B" terminal on the horn will cause it to sound.
How do you program a new remote to work on your 98 dodge caravan?
(95, 97, 98 & 99 Chry. T&C / Caravan, Grand caravan Follow the steps below (RKE Module Pin out diagram needed, info can be found on this forum) PREPPING: 1. Remove the upper dash panel to reveal the RKE Module 2. Unplug the RKE module (Some models have 2 plugs (ie. early Intrepids, eagles ect.) 3. Locate the GROUND & PROGRAM ENABLE WIRES. (Check forum for wire colors/location) these varies by year & model) ****Steps 3a, 3b & 3c IS OPTIONAL (For ease of FUTURE Programming)**** 3a. Run a Double Conductor Wire (16 or 18 awg) from the RKE Module (in dash) to any location BELOW the dash panel or glove compartment for easy access. 3b. Splice one wire to the PROGRAM ENABLE wire and splice the other wire to the GROUND wire (THIS Ground Wire is PREFERED) on the RKE Module connector. (MARK which one is the PGM ENABLE WIRE at BOTH ENDS with tape or a marker) 3c. Below the dash connect a S.P.S.T. (Single Pole Single Throw) Toggle switch to the 2 wires. (Note which position is ON/CLOSED) Programming an Initial RKE Remote 4.With Keyless Entry Remote(s) in hand Close ALL Doors insuring alarm is DISABLED (If appl.). 5. Turn the Iignition Key to the ON position (DO NOT START) 6. Ground the RKE Modules Program Enable Wire. For those whom install the switch toggle it to the CLOSED or ON Position. 7. Press and hold the unlock button on ANY REMOTE and HOLD IT. (You will hear a chime) 8. Release the button and press it again (single press) on the 1st remote. (You MAY hear a chime again) 9. Press ANY Button on the next remote. This is #2 (You will hear a chime) 10. Press ANY button on additional remotes (IF NEEDED) (you will hear a chime) 11. When finished Turn the Ignition Key OFF 12. Remove the GROUND from the RKE Module's PROGRAM ENABLE Wire or turn the toggle switch off. 13. Test each remote to see if it works. NOTE: If there is a problem with programming you may need to: a. Remove the GROUND from the RKE Modules PGM Enable wire BEFORE turning off the Ignition Key. b. Ground the PGM Enable wire BEFORE turning ON the Ignition Key c. After hearing the 1st chime imediatle press any key on the remote and once that chime is heard imeduiatly press any key on the next remote. ect. d. Do NOT leave this terminal grounded! or the toggle switch ON/CLOSED WHATS HAPPENING: Physically Grounding the RKE Modules PROGRAM ENABLE Terminal does the SAME thing as the BCM (Body Control Module) does to the RKE Module when the scan tool/dealer tool "Enables RKE Remote Programming" You are simply grounding the PGM Enable terminal instead of the BCM doing it via the scan tool. Now ENJOY Locking & Unlocking you vehicle via the Remote!
How do you program a keyless entry remote for a 2002 dodge neon?
=== === # Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop). # Using your old RKE transmitter, already programmed to the car, press and continuously hold down the UNLOCK button for 4-10 seconds. # Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module. # A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes). # Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred. # You may reprogram your old transmitter back into the car if it still works correctly. If not you may program up to 4 new RKEs. # After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.
How do you reset or disable an alarm system on a 1996 Chrysler cirrus?
There is no way to permanently disable. The reset is with a RKE (remote) or by unlocking a front door with a key.There is no way to permanently disable. The reset is with a RKE (remote) or by unlocking a front door with a key.
What is the airport code for Roskilde Airport?
The airport code for Roskilde Airport is RKE.
Where is the rke receiver in a ram truck?
behind speedo cluster little black box
