0
- The interests of the individual in retaining their property, and the injury threatened by the official action
- The risk of error through the procedures used and probable value, if any, of additional or substitute procedural safeguards;
- The costs and administrative burden of the additional process, and the interests of the government in efficient adjudication
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you pass a five prong urine test?
Don't do drugs.
How do you test a 3 prong headlamp that is not installed?
With a 12 V battery and two jumper wires. One prong is ground and the other two are high and low beam.
What is the 3 prong test as it relates to title 9?
Prong one - Providing athletic participation opportunities that are substantially proportionate to the student enrollment, ORProng two - Demonstrate a continual expansion of athletic opportunities for the underrepresented sex, ORProng three - Full and effective accommodation of the interest and ability of underrepresented sex.
How do you test for groung on a two prong outlet?
Buy a tester. They are very cheap and will tell you at a glance if the outlets are wired correctly. The only other way is to remove the outlet and look see. But if it is a 2 prong outlet with no ground hole then it does not have a ground.
How do you know which wire is the positive or negative on a grey three pronged cord that you have to connect to a garbage disposser?
all wires should be color coded, that is black-hot, white-neutral, green-ground. national electrical code been in use since the dark ages. if the wires are not colored, take a continuity tester, test from the cord cap to each wire on the opposite end of the cord. the larger straight prong on the cord cap is the neutral, mark it with white tape, the smaller straight prong [parallel to the larger prong] is the hot, mark it black. the " u "shaped prong is the ground wire, the mosat important of the 3. mark it green. on the continuity tester, the light on the tester will light when you touch the correct prong to the correct wire
Dan's three test scores were 78 75 and 90 what was the average of his three scores?
The answer is 81. Simply add the three test scores and divide by three.
What are the steps of a diagnostic test?
There are three steps of a diagnostic test that are divided into three distinct stages. The three distinct stages are the PreStep, the RunStep, and the PostStep.
What is importance of a polarity test?
HERE'S AN EXAMPLE: IF THE POLARITY IS BACKWARDS AT A LIGHT FIXTURE THEN THE HOT (120VOLTS) WILL BE THE OUTSIDE OF THE LIGHT BULB SCREW SHELL AND THE MIDDLE PRONG INSIDE THE SOCKET WILL BE THE NEUTRAL -- THEREFORE WHEN YOU CHANGE THE BURNT OUT LIGHT BULB YOU WILL GET SHOCKED BECAUSE THE SCREW SHELL PART IS HOT!! IF WIRED CORRECTLY YOU WILL NOT GET SHOCKED BECAUSE THE HOT (120VOLTS) WILL BE INSIDE THE SCREW SHELL ON THE PRONG AND YOU WON'T BE TOUCHING THAT PART WHEN YOU CHANGE THE LIGHT BULB!!
What are the three methods of fiber identification?
The three methods of fiber identification are microscopic view,burning test,chemical test.
What 1973 US Supreme Court case held that obscenity must be defined by contemporary community standards?
Miller v. California, 413 US 14 (1973)In Miller, the Supreme Court established a three-prong test to determine whether something met the definition of obscenity.For more information, see Related Questions, below.
When changing a three prong outlet on a dryer to a four prong where can you connect the ground?
Answer for USA, Canada and countries running a 60 Hertz supply service.Dryer plug three to fourInstructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What are the three tests used to evaluate documents that claim to be historical?
The "Internal test", the "external test", and the "bibliographic test".
