i need the head bolt torque on a 04 chevi cavallier engine 2.2
What are the torque specs for a 1996 Chevy cavalier 2.2l
you torque the bolts until they are good and tight
In order to replace a timing chain for a 2003 Chevy Cavalier, a person will need remove the oil pan, crankshaft pulley and hub, timing cover bolts, and timing cover. Then the timing cover gasket, timing cover and bolts, crankshaft pulley, and oil pan will need to be installed.
what kind of car? each car has it own torque spec 2000 Chevy Cavalier
just take the bolts out i think there size 8mm
the longer (new bolts) are to torqued to 48lbs and the shorter ones are to be torqued to 45lbs then turn the bolts an additional 90 degrees the bolts need to be replaced with new one because they are streched when you torque them down
The 1996 Chevrolet Cavalier 2.2 liter engine had bolt torque specifications are 120 pounds. The head bolts should be torqued at 40 pound intervals.
The 2001 Chevy Cavalier 2.2 liter engine cylinder head bolt?ætorque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
NEED help is there a diagram with the bolts in the backseat of a 1998 chevy cavalier?
what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine
My 1997 Chevy Cavalier with 2.2L motor used a 15mm socket.
In the transmission held on by 3 bolts
The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
Inside a cover plate on side of tranny. 12 or 16 bolts, and without a lift it is almost impossible to get to.
Torque for 292 head bolts is 95 ft lbs
The 1997 Chevy Cavalier dashboard is held in place with for retaining bolts and eight retaining clips. Remove the retaining bolts and pry outward on the retaining clips.
For the 1996 Chevy S-10 4.3 liter, the torque specs for the crankshaft damper bolts is 70 ft. lbs. For the cylinder head bolts, the torque is 65 ft. lbs, and for the engine mount-to-head bolts, the torque is 35 ft. lbs. For the engine mount-to-frame bolts, the torque is 52 ft. lbs.
The 2000 Chevy Cavalier windshield washer tank is held in place with for retaining bolts. Remove the retaining bolts and the windshield washer tank will come out.
the torque spec for what?
The torque specs for a 235 Chevy include main cap bolts of 100 - 110. Its bellhousing bolts are 45 - 55, flywheel bolts of 50 - 65, and rod nuts of 35 - 45.
tighten the bolts to 46 ft lbs working from the center out and then go back over them and tighten them an additional 1/4 turn
I used a 7/32 socket but it's probably a metric. The heads are really soft so don't over-torque them.
on the (overhead valve engine) short bolts 43ft-lbs, long bolts 46ft-lbs. then an additional 90 degrees. on (overhead cam engine) short bolts 30ft-lbs, long bolts 26ft-lbs then an additional 90 degrees
The 2000 Chevy Cavalier cooling fan shroud is held in place with 10 retaining bolts. Remove the retaining bolts and the cooling fan shroud will come off.
you are suppose to replace head bolts they stretch and head will not torque right. When you buy the new gasket, order new bolts.
The cylinder head bolt torque specs for a 1995 Chevy S10 2.2L are as follows: 1st: Torque the long bolts to 46 ft lbs, short bolts to 43 ft lbs 2nd: Turn all bolts an additional 90 degrees
head bolts - 22ft.lb. then 155 degrees. the little bolts on the side of timing chain - 26ft.lb 9 3 1 5 7 10 6 2 4 8
Tighten the1/4 inch bolts 7-9 ft. lbs of torque, and the 5/16 bolts to 12 ft. lbs. torque.
If the bolts are 3/8" or 10mm, the torque is about 45 ft.lbs.
If the bolts are 3/8-16, the torque would be 50 ft/lbs. If 7/16, 65 ft/lbs.
For the head bolts, 37lbs
torque especifications for Malibu 1999 3.1 engine
No the cylinder head bolts for 1.6L Chevy Aveo are TTY (Torque to Yield) bolts, meaning the bolts stretch after being torqured and cannot be reused without risk of breaking.
The 1997 Chevy Cavalier starter bolt size is 9/16 by 3.5" inches long. You will need three starter bolts to secure the starter.
Remove the belt from your 2004 Chevy Cavalier alternator. Remove the alternator wiring harness. Remove the alternator retaining bolts. Reverse the process to install your new alternator.
The 350 cubic inch Chevrolet intake manifold bolts have a torque specification of Haiti pounds psi. The bolts should be torqued at 40 pound intervals.
You can remove the windshield washer fluid tank from your 2001 Chevy Cavalier by removing the retaining bolts. There will be for retaining bolts at the bottom of the windshield washer fluid tank.
Disconnect the positive cable from your 2003 Chevy Cavalier battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
Remove the belt from your 2002 Chevy Cavalier alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.
Remove the wiring harness or the fan motor belt, depending on the year of your Chevy Cavalier. Remove the fan motor retaining bolts. The fan motor will come off.
Begin by removing the 2003 Chevy Cavalier alternator belt. Remove the wiring from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.
3.4 litre cylinder head torque is 37 ft lbs +90 degrees
No such thing as a DE-TORQUE pattern.Just remove the bolts from the heads from front to back.
It is 66 ft-lbs, and 46 ft-lbs for driveplate-to-torque coverter bolts.
I need the torque and secuense for the hea d bolts for a Chevrolet Malibu 2000 3.1
No, head bolt torque is much higher than rocker arms.
i have replaced my clutch to 10.5 diemter ,can i re use the morso flywheel/clutch bolts
You need to remove the lower transmission inspection cover.
11 Ft/ Lbs + 30 Degrees
what are the torque specs on body mount bolts