Best Answer

dO you mean the cylinder head torque ? if so it is 50 ft. lbs. then turn another 90 degrees. Always start from the center and work outward in a criss cross pattern.

User Avatar

Wiki User

โˆ™ 2005-01-19 09:19:55
This answer is:
User Avatar
Study guides

Create a Study Guide

Add your answer:

Earn +20 pts
Q: What is the torque setting and sequence on a 1997 Ford Ranger 2.3L?
Write your answer...
Related questions

What is the cylinder head torque sequence for a 1997 ford escort 2.0l?

torque head bolts and order ford 1997 2.0L picture if avalible please

Daewoo Cielo 1997 1.5 GLX cylinder head torque setting?

i need the torque setting s for the cylinder head DOHC of adaewoo cielo

What is the torque sequence for intake manifold on a 1997 mercury cougar 4.6liter?

The 1997 Mercury Cougar 4.6 liter engine intake manifold torque sequence should begin at each end of the manifold. Keep moving towards the center and alternating from and to end.

Torque settings for v6 commodore vs 1997?

Torque Setting for VS Commodore Harmonic Balancer Bolt- between 270-320 NM. The Best way is to check the bolt torque setting before you remove it.

What is the torque setting for spark plugs on a 1997 Geo Tracker?

Hi, The torque setting for the plugs is 20 ft lbs or 27Nm. Remember to use the anti-sieze compound on the plug threads. I hope this was timely enough for you. Steve H.

Cylinder head torque specifications for a 1997 Chevy 3100?

33 ft. lbs. plus an additional 1/4 turn on the bolt. Don't forget that there is also a torque sequence as well.

What is the torque on the bolts for shock absorbers on a 1997 ford ranger?

Ford recommends that you turn the bolt sideways and tighten with your fingers until they hurt.

What are the torque specs for the exhaust manifold on a 1997 Ford Ranger 3.0 engine? You can almost (actually all) torque specs here for most motors, just type in ur vehicle make and model at the home page. Good luck

1997 Honda cr 125 jug torque spec?

the torque spec for a 1997 cr125 cylinder head is 20ft pounds of torque.

Where is your torque conversion sensor on 1997 Dodge Intrepid?

where is torque conversion sensor on my 1997 didge intrepid?

What is the plug gap setting for 1997 Ford Ranger 2.3L?

.044 inch ( according to ) but check your engine compartment decal

What is the lug nut torque for a 1997 gmc z71 1500?

Lug nut torque 1997 gmc k1500

When was Phantom Ranger created?

Phantom Ranger was created in 1997.

How many quarts of oil in a 1997 2.3L ranger?

A 1997 2.3L Ranger will hold four quarts of oil.

Where is the carburetor located in a 1997 Ford Ranger?

The 1997 Ford Ranger engines are fuel injected , so no carburetor

What are the ratings and certificates for Ranger - 1997?

Ranger - 1997 is rated/received certificates of: Germany:BPjM Restricted

What is the rear hub nut setting on a Renault Megane 1.4 1997?

The torque settings for the rear hub nut (in the Haynes manual) is 175Nm or 127lb ft.

1997 Honda civic ex cylinder head torque specs?

What is the head torque specs on a 1997 Honda CRV

What is the torque setting for a 416 rover twin ohc head bolts 1997?

Engine code K16-1.6 Head torque Stage 1. 20Nm Stage 2. + 180 degrees Stage 3. + 180 degrees.

Will a 1997 Aerostar transmission fit in a 2000 Ford Ranger?

Will a 1997 Aerostar transmission fit in a 2000 ford ranger?

Diagram to ford 1997 ranger?

The diagrams of the different systems in a 1997 Ford Ranger can be found in a Ranger service manual. The manual is available for purchase in most auto parts.

Cylindear heads torque Dodge Dakota 1997?

4 cylinder: Bolt 7 is on the front driver's corner. # Tighten all bolts in sequence (1 through 10) to 30 N·m (22 ft. lbs.) torque. # Tighten all bolts in sequence (1 through 10) to 61 N·m (45 ft. lbs.) torque. # Check all bolts to verify they are set to 61 N·m (45 ft. lbs.) torque. # Tighten bolts (in sequence): # Bolts 1 through 6 to 149 N·m (110 ft. lbs.) torque. * Bolt 7 to 136 N·m (100 ft. lbs.) torque. * Bolts 8 through 10 to 149 N·m (110 ft. lbs.) torque. # Check all bolts in sequence to verify the correct torque. All "V" engines: Starting at top center, tighten all cylinder head bolts, in sequence, to 68 N·m (50 ft. lbs.) torque , Repeat procedure, tighten all cylinder head bolts to 143 N·m (105 ft. lbs.) torque. Repeat procedure to confirm that all bolts are at 143 N·m (105 ft. lbs.) torque.

Torque specs for a 1997 Acura 3.2tl?

There are dozens of torque specifications for your 1997 Acura 3.2 liter engine. A complete list of torque specifications can be obtained from most Acura dealerships.

When was Super Ranger Kids created?

Super Ranger Kids was created in 1997.

How do i change timing belt for 1997 ranger 2.3 liter?

show me a picture and diagram of 1997 ford ranger timing belt replacement