Want this question answered?
NOTEStep 1: Tighten all bolts to 22 ft. lbs.Step 2: Tighten all bolts to 51 ft. lbs.Step 3: Loosen all bolts, in reverse torque sequence, by 180°Step 4: Loosen all bolts, in reverse torque sequence again by 180°Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs.Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs.Step 7: Tighten all bolts, in torque sequence, by 80-90°Step 8: Tighten all bolts, in torque sequence, again by 80-90°
{| |- | NOTE Step 1: Tighten all bolts to 22 ft. lbs. Step 2: Tighten all bolts to 51 ft. lbs. Step 3: Loosen all bolts, in reverse torque sequence, by 180° Step 4: Loosen all bolts, in reverse torque sequence again by 180° Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs. Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs. Step 7: Tighten all bolts, in torque sequence, by 80-90° Step 8: Tighten all bolts, in torque sequence, again by 80-90° |}
Fist tighten to 50lbs in sequence,rhen to 60lbsin sequence and then to 65-72 ft lbs in sequence. Wait about ten minutes then recheck and tighten to the 65-72 ft lbs.
18 foot pounds
sequence is from the center out. torque in 3 stages. first 25 ft lbs second tighten 90 degrees [1/4] turn third tighten 90 degrees [1/4] turn. you're done.
Irrelevent. Just tighten the thing down and be happy.
The torque spec is 89 in-lbs not ft lbs. Tighten in sequence from the inside out.
Tighten the bolts to 60 nM (44 ft. lbs.) in sequence. Tighten the bolts to 60 nM (44 ft. lbs.) in sequence.
just start in the middle and tighten in circler pattern
Just criss-cross on the bolts and don't tighten them all in sequence, just like tightening lug nuts on a wheel.
Torque is 76Nm from memory and you will require a 10mm Allen key wrench drive
4 cylinder: Bolt 7 is on the front driver's corner. # Tighten all bolts in sequence (1 through 10) to 30 N·m (22 ft. lbs.) torque. # Tighten all bolts in sequence (1 through 10) to 61 N·m (45 ft. lbs.) torque. # Check all bolts to verify they are set to 61 N·m (45 ft. lbs.) torque. # Tighten bolts (in sequence): # Bolts 1 through 6 to 149 N·m (110 ft. lbs.) torque. * Bolt 7 to 136 N·m (100 ft. lbs.) torque. * Bolts 8 through 10 to 149 N·m (110 ft. lbs.) torque. # Check all bolts in sequence to verify the correct torque. All "V" engines: Starting at top center, tighten all cylinder head bolts, in sequence, to 68 N·m (50 ft. lbs.) torque , Repeat procedure, tighten all cylinder head bolts to 143 N·m (105 ft. lbs.) torque. Repeat procedure to confirm that all bolts are at 143 N·m (105 ft. lbs.) torque.