0
A fillet weld is a triangular weld with sides of a width, w by w . The throat is the thinnest portion, which is w divided by square root of 2. The throat thickness is used in stress calculations
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is fillet welding?
A fillet weld is the joint of 2 pieces of material, usually at a 90 degree angle. see http://www.unified-eng.com/scitech/weld/fillet.html
Leg or filet weld?
Leg of the weld. Fillet is the part you cut off e.g. a corner...
How do you measure filet weld?
In a fillet weld, the leg and size are the same for the convex weld.
Why is filet weld necessary while welding slip on flanges to a pipe end?
It is the only type of weld you can make to seal this type of joint. There are flange ends that can be welded onto pipe with a butt weld, but sockets and slip-ons must be fillet welded.
What is Socket weld?
A socket weld is a pipe attachment detail in which a pipe is inserted into a recessed area of a valve or fitting, and then fillet welded between its outside diameter and the fitting end. Generally used for piping whose nominal diameter is 2 inches (50 mm) or smaller.
What is the ratio between the leg length and the throat thickness on a mitre filet weld with equal leg lengths?
it depends on the fillet welds dimentions and fit up requirements
What is fillet welding?
A fillet weld is the joint of 2 pieces of material, usually at a 90 degree angle. see http://www.unified-eng.com/scitech/weld/fillet.html
Leg or filet weld?
Leg of the weld. Fillet is the part you cut off e.g. a corner...
How long does it take a human to weld a 1 foot fillet weld?
It depends on the thickness and type of materials being welded.
What is the filet weld size required for weldolets to main pipe joint?
wildly welding main pipe the are fillet weld or butweld
What is definition of the under run in filet weld?
A fillet weld in any single continuous weldmay underrun the nominal fillet weld size specified by2 mm [1/16 in] without correction, provided that theundersize portion of the weld does not exceed 10% of thelength of the weld. On the web-to-flange welds on girders,underrun shall be prohibited at the ends for a lengthequal to twice the width of the flange.
What is filleted?
A fillet weld is the joint of 2 pieces of material, usually at a 90 degree angle. see http://www.unified-eng.com/scitech/weld/fillet.html
Butt-weld and grrove weld?
First, Butt-weld is short for a butt groove. Welding in a butt-groove starts at the throat of the butt-groove. The first weld point could be a tack-weld: holding the two materials to be welded together. The throat is measured and filler metal and electrode are determined to create the root pass.
What is the meaning of filet weld?
The word fillet is used to describe a radius or angle at the joint of an angle instead of a shrap corner. It is sort of like when you use caulk to fill in the sharp corners when you are making a counter top. In a fillet weld you contact both peices of metal being joined at the 90 degree angle to "fill in" the joint.
How do you measure filet weld?
In a fillet weld, the leg and size are the same for the convex weld.
Why is filet weld necessary while welding slip on flanges to a pipe end?
It is the only type of weld you can make to seal this type of joint. There are flange ends that can be welded onto pipe with a butt weld, but sockets and slip-ons must be fillet welded.
What is the Five parts of a filet weld?
leg,toe,face,throat,root joint
