0
Flushometer 1" -11/4"=Tank type 3/8" IPS 5/8 OD copper or tank supply 3/8 compression=
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where is the flush valve of a toilet?
The water supply line attaches to it on the bottom of the tank. The actual valve is at the top of this tube.
How do you replace a flush valve in a toilet?
Have the new valve in hand. Cut the toilet water supply off at the commode, or even at the street meter box.Remove water tube or pipe supply and old flush valve. Install new valve and new supply line if required.
How do you install wax seal for toilet?
1. First loose the bolts that connect it to the flange on the floor and place the toilet in the bathtub 2.Turn off the water supply 3. Remove the lid of the toilet tank and flush the toilet 4. Use a plastic cup & dry sponge to scoop out water and dry up water drop. 5. Disconnect the water supply tube by turning the compression nut on the water supply valve. 6. use a flat head screwdriver to pry the caps from the washers at the base of the toilet. 7. Remove the nuts by using a wrench from the bolts. 8.Place the nuts, washers, and caps properly. 9. Hold the toilet under the bowl and rock it gently back and forth to break the old wax seal. 10. Lift the toilet off of the floor and set it down on a blanket, a piece of cardboard or in the bathtub. For more information visit mytoiletspares.co.uk
Where is the gas filter on a 1995 grand am?
They are usually located under the car. It should be a silver tube about the size of a toilet paper tube with steel lines running in and out of it.
Why is there already water in toilet bowls?
Under what circumstance? New toilet, when you turn the water on, water goes down the overflow tube to fill the bowl. You don't have to flush it the first time to fill the bowl.
What does it mean when there is only a little water in the toilet?
Partical stoppage. Bad Venting , Refill tube not working
What does the hose that goes from the toilet valve to the overflow do?
That device is called the refill tube. This allows water to go down the overflow tube to refill the water closet bowl while the tank is filling.
How high is 2 mL of water in a test tube?
It depends on what size test tube you are using.
Why does toilet inlet tube squirts water out of tank?
Is the small tube from the inlet to the overflow tube in place? Sometimes the gasket in the top of the fill valve will go bad and let it spray out of the top.
What would cause the toilet to make a loud high pitched sound when flushed?
On a syphon type, the diaphragm will scream if perforated or cracked. Depending on which system you have fitted, this could be anything from the ball valve to the flap valve and all points between.Below are instructions to change something completely. If you recognise what system the contributor is referring to all is well. For the rest of us it makes little sense.Explanation of a repair to an unspecified flush systemI don't know why but follow these instructions EXACTLY to fix it.Turn off the water supply to the toilet. Follow the hose attached to the bottom of the toilet tank to the cut-off valve. Turn this valve clockwise to turn off the water. Empty the tank by flushing the toilet, then dry out the toilet tank using old towels or a sponge. Place a bucket under the toilet tank to catch any water that is still in the tank.Unscrew the nut holding the hose to the bottom of the tank with vice grips or channel locks.Remove the nut screwed on to the toilet pump. This is under the toilet tank. After you loosen this nut, you may need to hold the toilet pump with one hand while removing the nut with the other because the toilet pump may turn with the nut.Remove the clip attached to the refill tube from the overflow pipe. Remove the toilet pump from the toilet tank.Attach the refill tube that came with your replacement toilet pump to the new toilet pump. Slide one end of the refill tube over the nipple on the toilet pump to cover the nipple completely. Attach the angle adapter to the other end of the refill tube.Place one of the shank washers that came with your replacement toilet pump on the threaded shank of the new toilet pump. Place the threaded shank into the hole in the bottom of the toilet tank.Fit the other shank washer over the threaded shank and push the washer firmly against the toilet tank.Replace the nut on the threaded shank of the toilet pump and tighten fully.Clip the refill tube to the overflow pipe using the angle attachment provided.Screw the water supply hose tightly onto the threaded shank. Turn the water supply back on and check for leaks. If water leaks from around the new toilet pump, check to make sure both shank washers are firmly in place and tighten both nuts fully.
When I turned on valve to toilet after being off for a while no water is filling the tank?
Make sure your main water is turned on by turning on another sink or bath and if it is then turn your toilet valve off and on a couple times and see if any water comes out in your tank. If still no water is filling the tank then shut off the valve and take the supply tube off the valve and turn the valve on slowly to see if you have any water comming out. If still no water then your valve is plugged or your pipe to the valve is plugged which then you would need to clean out your valve or lines with the whole house water shut off. Sometimes I have seen that the plug is in between the valve an supply pipe connection and as soon i take the supply pipe off and turn on the valve it works just fine even when I put the supply pipe back to the toilet. I don't think it would be in your fill valve in your toilet tank unless you have pressure assist tanks and with them all you need to do is take out the screen inside them.
Can a toilet paper tube your weight?
no
