0
A 'tap' is a connection made part-way along the length of a transformer's winding. In the case of a standard North American distribution transformer, the 240-V secondary winding is centre tapped and earthed, providing both a 240-V (across the entire secondary) and a pair of 120-V (between each end, and the centre tap) supplies to a building.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the difference between an ordinary transformer and a center-tapped transformer?
An ordinary transformer has two input/output terminals but a center tapped transformer has 2 input and 3 output terminals. One is taken from the center for a ground connection. This causes it to get 50% of the actual value. And ordinary transformer contains 2 windings. An autotransformer has one.
What is a multiple secondary transformer and why is it used?
One example would be for a vacuum tube, which uses two secondaries: one of low voltage to heat the filament, one of high voltage to cause thermionic emission.AnswerYou are probably referring to a multiple-tapped secondary, rather than a multiple-secondary (which implies several secondary windings). Multiple-tapped secondaries are used whenever you want a range of different secondary voltages -as per the example in the first answer.
Why transformer does not rotate when its secondary is connected to bearing?
How do you connect the transformer's secondary to the bearings.
How does a buck-boost transformer work?
A Buck Boost transformer is an auto transformer with a small primary to secondary voltage difference. It effectively adds or subtracts a few windings to the secondary to increase or decrease voltage. Here is an example: Say I have a 110 v and want 120 v; I have an auto transformer with 120 windings, tapped at 110 and 120. If I connect the 110 connection to my incoming 110v line, the voltage at the 120 tap will be 120v.
Why am you losing half the voltage when rectifying secondary side of center-tapped transformer to DC via two 1n4007 diodes?
I think the answer is: if you input voltage to a grounded center-tapped secondary transformer winding, only 1/2 the voltage is applied to each rectifier at a time (sine wave), therefore the rectified voltage measured would be 1/2 that of the total voltage. The peak voltage would be 1.4 x RMS. Hope this helps.
Where are center tapped transformers used?
The transformer that feeds your house is a center tapped transformer. Primary 7200, Secondary 240. The 240 volt secondary is center tapped to give you 120 volts on either side of the tap. Hence house voltage is 120 / 240 volts.
What is approximate turns ratio of the centre-tapped transformer used?
It depends on the voltage ratio of the transformer. If you know the primary and secondary voltages, then you can work it out for yourself.
What will be the output at lower half of 24v center-tap transformer?
If the secondary winding is 'centre tapped', then the value of voltage appearing across each 'half' will be the same. For a 24-V secondary, this will be 12 V.
What is the difference between an ordinary transformer and a center-tapped transformer?
An ordinary transformer has two input/output terminals but a center tapped transformer has 2 input and 3 output terminals. One is taken from the center for a ground connection. This causes it to get 50% of the actual value. And ordinary transformer contains 2 windings. An autotransformer has one.
What is a multiple secondary transformer and why is it used?
One example would be for a vacuum tube, which uses two secondaries: one of low voltage to heat the filament, one of high voltage to cause thermionic emission.AnswerYou are probably referring to a multiple-tapped secondary, rather than a multiple-secondary (which implies several secondary windings). Multiple-tapped secondaries are used whenever you want a range of different secondary voltages -as per the example in the first answer.
If you have a transformer with 25.2V center-tapped secondary with two 1N4002 silicon diodes in a full-wave rectifier What is the peak value of the dc pulses?
a: 25.2 x 1.41 with no load
What is the difference between transformers and autotransformers?
A transformer or, more-properly, a mutual transformer, has two windings, the primary and the secondary, which are electrically-isolated from each other, with the secondary voltage induced through mutual induction. An autotransformerconsists of one tapped winding, so the secondary circuit is not electrically isolated from the primary circuit. An autotransformer may be used to either increase or decrease the primary voltage, depending how it is connected.
What is circuleting current?
Usually this is a reference to current that is flowing that you don't want to flow - such as circulating current flowing through two parallel transformers, where one is tapped too high in relation to the other. This will cause the secondary voltage of one to be higher than the other, inducing current to flow from the higher tapped secondary into the other, up onto the primary and back to the higher tapped transformer primary.
Why transformer does not rotate when its secondary is connected to bearing?
How do you connect the transformer's secondary to the bearings.
How does a buck-boost transformer work?
A Buck Boost transformer is an auto transformer with a small primary to secondary voltage difference. It effectively adds or subtracts a few windings to the secondary to increase or decrease voltage. Here is an example: Say I have a 110 v and want 120 v; I have an auto transformer with 120 windings, tapped at 110 and 120. If I connect the 110 connection to my incoming 110v line, the voltage at the 120 tap will be 120v.
Why am you losing half the voltage when rectifying secondary side of center-tapped transformer to DC via two 1n4007 diodes?
I think the answer is: if you input voltage to a grounded center-tapped secondary transformer winding, only 1/2 the voltage is applied to each rectifier at a time (sine wave), therefore the rectified voltage measured would be 1/2 that of the total voltage. The peak voltage would be 1.4 x RMS. Hope this helps.
Is there any application where center tap rectifier is preferred over bridge rectifier?
For a center tapped full wave rectifier transformer secondary gives a voltage that is 2Vm. For a bridge rectifier it is Vm.
