Graphite is a naturally occurring mineral that has many useful properties. It is a dry lubricant meaning it does not require any water or oil to lubricate surfaces. Graphite is useful as a dry lubricant because of its following properties:
These properties make graphite a useful dry lubricant in many applications such as in the manufacture of locks automotive parts and even as a coating for medical instruments.
There are a couple of possible answers. Molybdenum is used to lube engine parts during rebuild as it has a lower coefficient of friction than steel. However, the person asking the question was probably thinking of carbon in the form of graphite, which is used as a general purpose dry lubricant where it's not expected that the surfaces will become too hot.
the demine
graphite is preferred in brass locks and alike as oil can penetrate the closely moving parts, then if the oil drys up it welds the parts together and that's the end of it . graphite is a dry very fine powder. and acts like billions of tiny marbles. causing the surfaces to slip nicely..... no good in car engines though as it has little cooling properties and will not flow around the engine.
To clean graphite grease from curtains, gently rub with a soft eraser to remove excess graphite. Spray on a dry-cleaning solution and apply a dry spotter. Moisten a dry pad with the dry spotter and rub into the dry spotter on the stain. Apply dry spotter to a clean pad and lay on the stain for at least 30-minutes. Spray with the dry-cleaning solvent again and allow to air dry.
If YOU write in this area, your question goes to the "already answered" bucket- Besides its use as jewelry, Diamond is used where anything incredibly hard is needed. Diamond (dust) is used to make saw blades and drill bits that can cut through just about anything. Graphite, while also composed of carbon, has an entirely different crystal structure, and different uses. Graphite is used as an electrical contactor (a brush) in electrical motors. It makes a great dry lubricant for things like locks, and when mixed with clay, forms the "lead" for ordinary pencils.
graphite as a dry lubricant is sold in powdered form in most hardware stores.
An advantage for graphite is that it can be used as a dry lubricant on electrical appliances.
According to Experts, graphite is used as a lubricant because it is dry lubricant and a solid material with a greasy feel which makes for a good source for applications where oil cannot be used. Graphite is used inside pencils. It slips easily off the pencil onto the paper and leaves a black mark. Graphite is also a component of many lubricants.
According to Experts, graphite is used as a lubricant because it is dry lubricant and a solid material with a greasy feel which makes for a good source for applications where oil cannot be used. Graphite is used inside pencils. It slips easily off the pencil onto the paper and leaves a black mark. Graphite is also a component of many lubricants.
carbon and graphite are one in the same, graphite is a form of carbon a use for graphite is the lead in your pencil (it's not actually lead, it's graphite) and it is also a good lubricant ;)
Graphite is used as a dry lubricant and steel hardener and for brake linings and the production of "lead" in pencils
Carbon is an element on the periodic table.
A dry lubricant is a material that is able to reduce friction between two surfaces without the need for a liquid-based lubricant. Examples include graphite and molybdenum disulfide, the two most common dry lubricants, but hexagonal boron nitride and tungsten disulfide can also be used.
According to Experts, graphite is used as a lubricant because it is dry lubricant and a solid material with a greasy feel which makes for a good source for applications where oil cannot be used. Graphite is used inside pencils. It slips easily off the pencil onto the paper and leaves a black mark. Graphite is also a component of many lubricants.
There are a couple of possible answers. Molybdenum is used to lube engine parts during rebuild as it has a lower coefficient of friction than steel. However, the person asking the question was probably thinking of carbon in the form of graphite, which is used as a general purpose dry lubricant where it's not expected that the surfaces will become too hot.
you should either use a dry lubricant like graphite or a 100% silicone. anything else will make the plastic deteriorate.
the demine