0
factory air pressure norm is 80 psi
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can you use same hoses both for pneumatic and hydraulic?
not quite, it depends on the pressure of system, but hydraulic tends to be high or could be very high pressure, and pneumatic is often lower pressure. the low grade rated pressure hose/ pipe would fail and burst/ causing injury.
Is a hairdryer a pneumatic system?
A hair dryer is actually not a good example of a pneumatic system. A pneumatic or hydrologic system uses fluid (gas or liquid) to transfer force over a distance. Hair dryers lack almost all components found in a pneumatic system. The internal operation of a hair drier is simple, a fan creates a high pressure air pocket on the heating element, and this high pressure air pocket cause air to be sucked in the back, and pushed out the blowing end. Hopefully this helps your endeavors. J. Salsieder
What are some examples of pneumatic devices?
Yes there is. Pneumatic valve springs. They are metal bellows that have air in them. Their use is in replacing metal wire springs in a high-speed combustion engine. An example would be formula one engines.
How do you decide when to use pneumatic or hydraulic power?
when high power transmission is involved then hydraulics is the best option this because there are hydraulic fluid available to suit the various pressure levels. liquids have almost zero compressibility. in pneumatic system air is the working fluid, too high pressure could compress the air to such an extent to liquify it causing the tubes to crystallize and burst it. air is highly compressible and hence power loss should also be accounted for the compressed air so only low power systems possible here eg: pneumatic door openers .
Can a pneumatic control valve be used with hydraulics?
No. There are a few reasons why a pneumatic control valve can not be used with hydraulics applications. Firstly, pneumatic seals are incompatible to the chemical properties of hydraulic oils and they do not have the strength to accommodate the high pressures produced by a hydraulic system. Secondly, pneumatic valves are not designed for high pressure operation and the component would get damaged, burst or crack. Finally, the tolerances within pneumatic components would allow by-passing due to the slacker tolerances compared to hydraulic components. By-passing causes all sorts of problems by itself: Over-heating, leaking, internal structure damage of the component.
How do you to select a pneumatic hammer which can give 25 g force?
It depends on air pressure in the pneumatic system. You pneumatic systems for high and low air pressure to force change. This is the compressor power.
Can you use same hoses both for pneumatic and hydraulic?
not quite, it depends on the pressure of system, but hydraulic tends to be high or could be very high pressure, and pneumatic is often lower pressure. the low grade rated pressure hose/ pipe would fail and burst/ causing injury.
How is a hairdryer a pneumatic system?
A hair dryer is actually not a good example of a pneumatic system. A pneumatic or hydrologic system uses fluid (gas or liquid) to transfer force over a distance. Hair dryers lack almost all components found in a pneumatic system. The internal operation of a hair drier is simple, a fan creates a high pressure air pocket on the heating element, and this high pressure air pocket cause air to be sucked in the back, and pushed out the blowing end. Hopefully this helps your endeavors. J. Salsieder
Is a hairdryer a pneumatic system?
A hair dryer is actually not a good example of a pneumatic system. A pneumatic or hydrologic system uses fluid (gas or liquid) to transfer force over a distance. Hair dryers lack almost all components found in a pneumatic system. The internal operation of a hair drier is simple, a fan creates a high pressure air pocket on the heating element, and this high pressure air pocket cause air to be sucked in the back, and pushed out the blowing end. Hopefully this helps your endeavors. J. Salsieder
What are some examples of pneumatic devices?
Yes there is. Pneumatic valve springs. They are metal bellows that have air in them. Their use is in replacing metal wire springs in a high-speed combustion engine. An example would be formula one engines.
Does a high-pressure system have a low-pressure or high-pressure center?
A high pressure systems has a high pressure center.
What kind of weather does high air pressure cause?
High Pressure, in this case we are talking about a High Pressure System. A High Pressure System doesn't allow clouds to form, which means you can get great weather from this type of system.
What has the author L R Botting written?
L. R. Botting has written: 'The response of a high-pressure pneumatic servomechanism to step and sinewave inputs' -- subject(s): Pneumatic control, Servomechanisms
How do you decide when to use pneumatic or hydraulic power?
when high power transmission is involved then hydraulics is the best option this because there are hydraulic fluid available to suit the various pressure levels. liquids have almost zero compressibility. in pneumatic system air is the working fluid, too high pressure could compress the air to such an extent to liquify it causing the tubes to crystallize and burst it. air is highly compressible and hence power loss should also be accounted for the compressed air so only low power systems possible here eg: pneumatic door openers .
Is 157 102 high blood pressure?
A blood pressure reading of 137/78 is not considered high. When the top number is 140 or higher that is considered high blood pressure.
Are anticyclones low pressure system?
No, an anticyclone is a high pressure system. A cyclone is a low pressure system.
Can a pneumatic control valve be used with hydraulics?
No. There are a few reasons why a pneumatic control valve can not be used with hydraulics applications. Firstly, pneumatic seals are incompatible to the chemical properties of hydraulic oils and they do not have the strength to accommodate the high pressures produced by a hydraulic system. Secondly, pneumatic valves are not designed for high pressure operation and the component would get damaged, burst or crack. Finally, the tolerances within pneumatic components would allow by-passing due to the slacker tolerances compared to hydraulic components. By-passing causes all sorts of problems by itself: Over-heating, leaking, internal structure damage of the component.
