0
What size bolts to use to replace the rivots in window regulator?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do I replace an old window regulator on a 1989 Oldsmobile 88Royale with a new one and is the regulator the same thing as the motor?
The regulator is the part that raises the window. Can be a notched curved piece and a X shaped arm that raises the window or a plastic strip that runs in a grove. The motor can be changed. I belive regulator and the motor are both held in by rivots. These can be drilled out and replaced with bolts.
How do you replace 3000 gt door window regulator?
First, lower window approximately half way. This allows you access to the bolts that attach window to the regulator. Remove door panel. Using a 10mm wrench, remove the two bolts that hold window to the regulator. Then there are two upper and two lower bolts holding the regulator to the door. Then you remove the three bolts for the window motor which is toward the front of the door. You have to also disconnect the plug for the windo motor to remove the entire window regulator and motr that are all one unit. Replace the unit in the reverse way.
How do you replace window regulator 1991 3000gt?
Take the door panel off,you will need to remove 3 bolts for the window motor and then 3bolts(maybe4) that hold the regulator to the window
How do you replace just a window regulator not the motor?
You have to drill the rivets on the motor separating it from the regulator. The new motor then mounts to the regulator and you insert the new bolts where the riverts were.
How do you replace the driver's door electric window motor you have a 1999 gmc safari van slt?
I believe that replacing the motor requires replacing the regulator and motor as an assembly. However I drilled the rivots out and repaired my old motor, beware it is difficult to get bolts that will clear the mechanism to refasten it back in place.
How do you replace a rear window on a 1984 K5 blazer?
To replace your window, you need to have the window rolled up. On the regulator(that is the little arm that connects to the metal peice on the bottom of the window) is 11mm bolts. If you take those four bolts out, the metal sleeve on the bottom will come off. Clean out the old silicon. Put in new. Replace bolts.
How do you replace a 97 vw jetta window regulator with motor the window is up and you can't figure it out please help?
u have to have the window rolled down about 4 inches. If the window is stuck up force it down and you can access 2 bolts holding it to the window. Only force it if you plan to replace the regulator.
How do you replace the automatic window motor and regulator for the drivers side window on a 1994 Jeep Cherokee Sport?
Remove the door panel. Remove the bolt that fastens the regulator to the window. Remove the 3 bolts that hold the regulator assembly to the door. Squeeze the entire assembly through the largest hole and replace with a new assembly in reverse order.
How do you replace 1995 Toyota Celica power window regulator?
remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.
How do i change the right rear window motor on a 2002 deville?
It is best to replace entire regulator as one unit. Remove door panel. Remove bottom nut of regulator, and remove two top nuts of regulator. Loosen two bolts on bracket holding window. Support window, and carefully remove regulator as one unit.
How do you take out a power window motor from a 1999 dodge caravan?
first take of the door panel. Next you will see the window regulator. The there is going to be 4 bolts or so that you are going to need to take off, after that unhook the window. Then pull the whole window regulator out and replace the whole thing
How do I replace a window regulator for a 94 Toyota Camry?
Remove the door panel. Use a coat hanger or ty rap to secure the window in the up position. Disconnect the wiring from the motor. Remove the bolts that secure the glass to the regulator. Remove the regulator. Install motor on new regulator. Installation is the reverse procedure. 6 to 8 bolts in entire process. Good Luck. CAH
