0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you size a phase converter to run a 3 phase welder?
From the nameplate on the welder you find the amperage that the welder draws at the three phase voltage that you are going to use. This amperage is used to size the phase converter. This amperage is also used to size the breaker that will feed the phase converter and wire size for the installation.
What breaker size do you use for a 270 Kw power rated equipment and power supply of 380 vac 3 phase?
I=270000/380/1.732 I=410A USE: 500A CIRCUIT BREAKER
How do you calculate breaker capacity of 10 hp three phase induction motor?
The first thing you have to do is find the full load amps of the motor. The wire size feeding the motor has to be 125% of the full load current. The breaker is usually 250% of the full load current. If the voltage and amperage had been added to the question the exact breaker size could have been calculated.
What is the standard to select circuit breaker?
Add up your amps to calculate your breaker size. Add up your loads (amps), divide by 0.8, and choose that size breaker. If that number does not correspond to a standard size breaker you go to the next higher standard size breaker.
What is the size breaker per phase 200kva generator?
if you have 200 kva so it's 160 KW then ,you need 400 A MCCB and setting at 0.9 and use cable 4c.185 mm2 if the SMDB is nearby and all this will be change according to the ambient temperature and the electrical code used in your area
What size breaker do you need for 9000W at 440V 3 phase delta?
50amp but if considering the breaker cannot withstand starting current you need to size the breaker up.
What is the purpose of the 110 V single phase breaker?
The job of a breaker is to limit the amount of current that is applied to the size of wire that is connected to the breaker.
What is the breaker size for a10kw 380v 3 phase power supply?
10amp
How do you size a phase converter to run a 3 phase welder?
From the nameplate on the welder you find the amperage that the welder draws at the three phase voltage that you are going to use. This amperage is used to size the phase converter. This amperage is also used to size the breaker that will feed the phase converter and wire size for the installation.
What size breaker for a 208 volt single phase motor that pulls 1.4 amps?
208 volts is not a common single phase voltage but you could just size your breaker to the capabilities of the conductor. 208 is normally a phase to phase voltage <<>> Many 230 volt motors can be connected to lower voltage supplies. These motors can be connected to supplies of 208 and 200 volts. The code requirement is that the 230 volt full load amperage of the motor be increased by 10% and 15% respectively for wire sizing and breaker selection. To answer the question you will need a two pole 15 amp breaker.
Minimum breaker size 60 horsepower motor?
Need motor voltage, amperage and phase to give you an anwer.
What breaker size do you use for a 270 Kw power rated equipment and power supply of 380 vac 3 phase?
I=270000/380/1.732 I=410A USE: 500A CIRCUIT BREAKER
What size of breaker is use for 75 horsepower 220 volts 3 phase induction motor?
500 amp breaker with 250 mcm cu conductors, NEC list this motor as drawing 192 amps X 250% = 480amps go to the next standard size of breaker which would be a 500.
What type of appliance would be use a two pole 50 amp breaker?
In North America this size breaker could be used on a welding machine. A range in the home would use a 40 amp two pole breaker.
What size wire and breaker for a 240 volt single phase 20 kw electric furnace rated at 83.3 amps?
AWG #3 copper.
How do you calculate amp draw for 115v 1 phase and the breaker size?
To calculate the amp draw of a device you need to use one of the following three formula. I = W/E, I = E/R, I =√W/R. Once the amperage of the circuit is found then the size of the breaker can be established.
How is a 208 volt 3 phase electrical sub-panel wired?
Mark the phases red (phase) black (phase) and blue (phase) along with a white (neutral) and a ground (wire size depends on the main breaker amperage) the phases attach to the main breaker unless it is a breakerless panel attach the phases to the lugs on the bus bars top or bottom then connect the neutral to the neutral bus and the ground to the panel
