0
What size drill bit do you use to make holes in your fingerboard?
Wiki User
∙ 11y ago
More information is needed as to the purpose of the holes, and what a 'fingerboard' is .
Wiki User
∙ 11y ago
Anonymous
3 mm
Add your answer:
Earn +20 pts
What size holes would you drill in the pipe to make a burner for a pig cooker?
The holes for a pig cooker should be about a half inch to an inch wide. These holes must be drilled into a pipe for the cooker.
Do drill bits have a universal size?
Drill bits are not universal. You choose the size of the drill bit according to the size of hole you like to make.
What machine is used when holes must be made in a material very accurately?
That depends on the material and the size of holes. -I can do that on a drill press with a jig.
Which bit is specifically used to drill holes in concrete and masonry work?
A 40mm hole saw is more efficient than a drill bit for holes of this size.
Why is it best to use the right size of drill it in boring holes?
Because you presumably want your hole to be the right size, not too small or too big.
How much larger than the pipe size should the drill bit being used to drill holes in the floor joist be?
Wrong Question... You first determine the hole size required for the mine plan and then based on the air capacity and pulldown capacity of the drill rig you can determine the optimal drill pipe diameter to achieve productivity from the drill. What size is your drill? Air Capacity in CFM, Pulldown Capacity. What size does your drilled hole (diameter and depth) need to be to suit the mine plan (for the drill & blast process)?
How do you determine the drill size for tapped holes?
Google "tap drill sizes" and you'll get 19400 results. The formula for that calculation is searchable in Machinery's Handbook, but there are simple charts you will get in your search that can give you the answer for any size you need to know.
Why is the best to use the right size of drill bit in boring holes?
Because you presumably want your hole to be the right size, not too small or too big.
What size drill bit to use to drill holes for vertical blinds?
Depends which screws you are going to use. I usually use the #6 screws that come with blinds. They need no pre-drilling.
How do you make hole drilling where at the exit the drill has partial entry in to the wall thickness which makes the load nonuniform on the drill and hence drill breaks and size is not maintained?
There are a few ways of doing it depending on the exact geometry, size, and tolerance. You could drill the hole before cutting the profile that results in the partial entry. You could drill very carefully and slowly, stepping up the drill from a small size to the final size, if the smaller size would enter complete. You could make a fixture to fit over the part so the drill is guided into it. There are low melting alloys you can pour around the area to make a complete entry. You then melt the alloy away.
Bench drill press use?
A drill press is used to drill holes. To start put your wood or plastic in the vise. Now put your drill bit in. Make sure you only put the smooth part in the chuck. Now tighten your chuck with a chuck key. Make sure the bit lines up with your intended hole position. Now you can clamp your vise to the table of the drill press. Start the machine and bring the bit down slowly. Now it will start to cut . That is mainly what you need to know to use the drill press.ANS 2 - A drill press may be used for many jobs other than drilling conventional holes.With the use of different jigs, you can drill many repeated holes in the exact same place on objects.You can use Hole saws to drill bigger holes than is comfortable with a hand drill.You can use a 'Fly-bit' to make large holes in thin sheets of wood or plastics.You can stack many thin sheets to be drilled all at once.You can use Forstner bits to sink holes of any size to exactly the same depth many times.You can use 'milling bits' to make rough surfaces exactly flat and smooth.The medium to large drill press is an extremely versatile workshop tool if you know how to use it.
Is there a drill bit that can drill holes 2 millimeter wide if so please describe?
You simply use a 2mm drill bit, or if that is too difficult for you, select a 1/16 drill bit which is extremely close in size . -I consider both of these drill bits very common, so it's hard to understand anyone having a problem with it.
