A kilowatt is a unit of power, and energy is measured in kilowatt-hours, in other words 1 kilowatt flowing for 1 hour is one kWh of energy.
For an ordinary heat engine it is normal to use a round-number estimate of consumption as half a pound of fuel for one horse-power-hour, which is 0.746 kWh.
200 kW is theoretically 270 HP but you would need a 300-350 HP motor.
Well, if 80kW is your PEAK value, then you need an 80kw generator. If 80kW is your nominal current, you need to figure out what your peak current is. This will depend on the type of load. Is mostly motor loads? If so, your peak current may be significantly more than nominal, depending on the starting sequences of the motors. Clear as mud?
There is no way to answer without knowing the wattage rating of the 9 volt generator. A generator's wattage rating depends on the size of the wire in it, the wattage of the rectifiers if it is a DC generator, and the horse power of the engine or motor that is available to turn the generator.
The starter motor of a diesel generator is a DC motor. Depending on the size of the diesel engine the starter motor could be 12 volts or 24 volts. Sometimes more that one battery is used at the specific voltage. These batteries are connected in parallel to create more amp hour cranking power.
Need to know what the voltage of the motor is.
you need the current of motor or the KW/HP rating
You need a 5.5kw generator to run a 5.5kw motor.
A motor driving a generator to operate an electric car does not need to be as large as an engine that normally drives a car. This is because the engine must be made to provide the maximum power that the car requires wheras the generator motor only needs to provide enough to charge the batteries.The actual size depends on the size of the car and the batteries used.
I would say about 13 HP on it. Hope it helps!
you need around 60000 watts on a dc current
The sizing of the generator is dependant on the size of the electric motor driving the mixer.
A 5 kW generator would turn it over but if the full 30 hp of mechanical power is needed, that would require about 30 kW of electric power from the generator.
To answer this question the voltage and amperage of the unit must be stated. Once this is given the generator size can be calculated.
Prices vary for a Yamaha Generator depending on the size of the generator. The more wattage involved, the more you will need to pay. First you need to determine the size of generator you need then contact a local retailer.
When you refer to a 200 amp welder you are talking about the output side of the welder. What you have to do is find out what the input voltage and current of the welder is to calculate the size of a generator needed to operate the welder.
if your talking about a generator its not the hp of the engine its the size, rpm, and gearing of the generator motor
A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.A 1986 Ford Rel Lite motor home may need to be able to run multiple appliances. A 4kw generator will be powerful enough to run the necessities with no issues.
If you are talking about turning on and off the 1 HP pump you will need to know what voltage the motor is and buy the correct size switch to operate at that voltage.