0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you convert psi water pressure to gallons per minute?
First you need the size of the pipe and the volume of water supply. Pressure will vary during usage. Standard well system operates between 20-40 psi and city systems operate from 50-70 psi.
What is dn50?
It stands for Deutsches Normung=German standard and usually applies to dimensional information in the metric system. Hence DN50 is for 50mm.
What is the Unit weight of 50 nb ms pipe for structural use?
what is weight of 60 dia ms pipe
Draining Pipe?
form_title= Draining Pipe form_header= Keep your drainage clear with a new pipe. Do you need to remove an existing pipe?*= () Yes () No Where will the pipe be installed?*= _ [50] Do you currently have any other plumbing issues?*= () Yes () No
What is the pressure and gpm for a typical residential water well?
A typical deep submersible pump on a domestic well will be 5-10 gpm and will run up to 120 psi if not governed by a pressure switch at the holding tank. Most Home pressure switches are set to come on at 30-45 psi and shut off at 50-75 psi. This, coupled with the air pressure in the holding tank, means that home pressures of 50 -75 are normal.
How do you convert psi water pressure to gallons per minute?
First you need the size of the pipe and the volume of water supply. Pressure will vary during usage. Standard well system operates between 20-40 psi and city systems operate from 50-70 psi.
How many GPM through 1.5 inch pipe at 50 psi?
you need to know the viscosity of the liquid - molasses or alcohol?
My well is making 50 gallons of water per minute How do I convert 50 gpm to PSI?
gpm and psi are two different measures that are not directly related, though a change in one will affect the other. To get the pressure at a certain point in your piping, you would need to measure it. Or, if you know that your pump is rated for 50 gpm at 80psi (1 foot water column = 2.31 psi) and your pump is lifting a column of water 15' (34.65 psi), then you should have about 45 psi residual. If you have long runs of horizontal pipe you may need to add some for pipe friction also.
DN 50 valve size?
DN 50 means: "DN": Diametre nominel - Nominal diameter of the valve, and "50" is the size of the valve in [mm]. Alternative is NPS (Nominal pipe size in inches).
What does it mean for size DN 50?
DN": Diametre nominel - Nominal diameter of the valve, and "50" is the size of the valve in [mm]. Alternative is NPS (Nominal pipe size in inches).
What size Full Port Ball Valve do I need for 18 gallons of water at 50 psi?
Depends what size your pipe is
What size box is needed to hold 50 boxes that are 7x7x3?
350x350x150
What size wire is needed to run a 50' 20 amp curcuit?
12 gauge or bigger.
What is the cooling system capacity on a full size 1988 Chevy Blazer?
Antifreeze Needed 2 1/4 Gallons For a 50/50 mix
1997 ford f250 truck what size wrench is needed to take off the belt tensioner?
a T-50 star bit is needed to remove the bolt
Maximum flow at 50 psithourgh PVC?
Depends on the volume and the size of the pipe. Fill a 5 gal bucket and time it. This will give you gallons per minute.
How many gpm of water flow through a one inch pipe at 50 psi?
The question is a little more difficult to answer than you may think. Here is a link to the mathamatic concept, each pipe is different so you will need the material your using. http://knol.google.com/k/d-gardiner/how-to-calculate-pressure-drop-and/35e6sqhxsbdsg/2# My friend Jeff from Canadian Leak Detection says: The answer is 189 gallons per minute. Then: The rest of the story is that 189 gallons is nozzle flow. If the water flows down the pipe for any distance the friction will slow the flow a bit. So if you need really accurate flow rate I need more info.
