0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you fix rear shock absorbers on a Renault megane scenic?
loosen the wheel nuts and jack up the car ( use axle stands if available ). remove the wheel, Use a 22mm socket to remove the lower bolt and a 22mm 12 point socket to remove the top bolt. push the old shock absorber off and push the new one in and replace the bolts.ten minute job.
What is the rear shock absorber bolt size for a 2000 silverado?
The rear shocks take a 21mm wrench...
How do you repair or replace a broken lower rear shock bolt on a 1991 s10?
First jack the rear of the truck up. Relieving the shock of any pressure will allow the bolt of slide off easier. Remove the broken bolt and replace it with a new one.
How do you change the rear shock on a Yamaha Raptor 660?
First remove the compression from the shock by either propping up the rear of the bike or lifting up the rear of the bike. I tied the rear grab bar behind the seat to the ceiling. You will need to remove any skid plate for the swing arm as the shock assembly needs to go downward. You will also need to remove the muffler to allow sufficient room to remove the upper shock mount bolt . Loosen the bolts at the top of the shock with a 19mm wrench and socket. Do the same for the lower bolt using a pair of 17mm metric wrenches. Now remove the bolt that holds the shock linkage to the swing arm with a 17 millimeter wrench and socket. This will allow the shock and linkage to drop down word through the swing arm. If the shock and linkage do not drops down, adjust the height of the seat relative to the swing arm until it can drop through. Remove the upper bold holding the shock to the frame . You will need to push and wiggle the exhaust pipe out of the way to get the bolt out. This will only work if you previously removed the muffler.Now I remove the bolt that holds the bottom of the shock to the linkage. Now you should be able to remove the shock from the bike. The top and bottom of the shock have spacers that must be retained and reused. Now simply reverse the process to install the new shock. Good Luck. The Gremlin.
1989 caprice rear shock removeal. Bolts rusted. What size socket for the top bolts?
13 mm
What size bolt head is in a 2WD rear drive shaft on rear-end pinion yoke of a 1995 Ford Explorer XLT?
The bolt heads require a 12mm/ 12 point socket.
Where in the trunk is the top bolt for the rear shock on a 1989 Mercury Marquis?
ITS NOT IN THE TRUNK AT ALL. Well, THAT was a big help ... Doofus! The top shock bolt is not in the trunk, it is between the trunk floor and the rear axle. It is very hard to get at. You'll need to jack up the entire rear end of the car and let the wheels drop as far as they will go. Remove the wheels, look straight into the rear wheel well. Just forward of the axle and just above the frame arch is the top nut. You won't be able to get a socket on it, you will have to use a wrench. It is a pain in the butt! Have fun.
How do you remove the rear shock bolt on 1996 Pontiac Grand AM?
It can be accessed through the trunk on some cars.
How do you replace rear shock on Volvo s60 2.5T?
I wish someone answered this, I can't seem to be able to take off the top rear shock absorber bolt without it spinning with the top of the schock.
How do you remove the spare tire on a 2002 ford ranger?
You will need a ratchet and a socket to remove it. You get under the rear of the truck and you will see the bolt and bracket holding the tire in place. Remove the bolt and the bracket hinges downward. You will need a ratchet and a socket to remove it. You get under the rear of the truck and you will see the bolt and bracket holding the tire in place. Remove the bolt and the bracket hinges downward.
How do you replace the rear shocks on a Ford Windstar?
To remove rear shocks:# Raise and support the vehicle and remove the wheels# Put a jack under the rear axle and raise it slightly to take the tension off the shock# Remove the lower shock absorber bolt/nut and disconnect the shock from the rear axle.# Remove the upper shock absorber-to-chassis bolt to release the shock from the vehicleTo install rear shocks: # Attach the shock absorber to the upper mounting bracket and install a new retaining bolt/nut.# Using the jack you put under the axle, slowly raise the axle while guiding the shock into the lower mounting bracket.# Install a new retaining bolt/nut and tighten to 50-68 ft. lbs.Don't forget to put the wheels back on...----Your Windstar may not have shocks. Please verify. My Windstar has a X look in the back with coil springs and thus no shocks because that is handled by the X.
What torx socket is needed for your 2002 gmc sierra rear brake caliper?
12mm bolt on the rear. Like a 16mm nut style head on the slider. Hold the head of the pin to break the bolt loose.
