0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How expensive is correcting 20 amp breakers with 14 gauge wire?
If you plan to do it yourself fairly inexpensive.Depending on the type of panel you have breakers start as low as $3.00 for a 15amp breaker. If you are looking to have a professional do it you will probably pay at least $5.00 per breaker plus whatever the going rate for labor in your area is.
Can a 100 amp main have 2 50 amp breakers?
Yes.Additional InformationBreakers and fuses protect the wires to prevent fire. The 100 Amp breaker in the meter base (main) protects the wire from the meter base to the breaker panel. The 50 Amp breaker in the breaker panel protects the wire from the breaker panel to the outlet. Sometimes the 100 amp main breaker is located in the panel.If you are asking "Can you use two 50 amp breakers for the main breakers with a 100 amp service, then yes you can. The National Electrical Code allows you to use up to 6 breakers as the main overcurrent protection.
What is an electric shared neutral?
An electric shared neutral is the white or negative wire that is shared between two electrical circuits on a basic single phase system. Most electrical devices use 120 volts and require a "hot" wire and a neutral wire to operate. Some larger devices use 240 volts and require two "hot" wires to operate. Two circuit breakers in an electrical panel can share one neutral wire as long as the breakers are not on the same "leg" of power. When looking at an electrical panel there are usually two "legs" of power feeding all the breakers, each leg has 120 Volts to ground, if the "legs" are combined you will have 240 Volts. A neutral wire can be shared by two circuits as long as the breakers are on separate "legs". If someone needed to add two circuits in their home, the could run what is called a 3-wire romex, It has a black wire, a red wire, a white wire and a ground wire. The white wire is the neutral for both the black and red 120 volt circuits, and the breakers for the new circuits would need to be on separate "legs" in the panel.
What size wire is needed to feed a 125 amp sub panel from a 200 amp panel less than 200 wire feet away?
A #1 copper wire with an insulation rating of 90 degrees C is rated at 140 amps.
Is a 12 gauge wire on 20 amp breaker safe for a sub panel?
Yes, if you are running it no farther than 100 feet. If you are going over 100 feet use AWG # 10 wire on the 20 amp breaker.
What type of wire do you need to run a 60 amp sub panel with 3 20 amp single breakers in the panel?
I would use 4 AWG copper to be safe.
How expensive is correcting 20 amp breakers with 14 gauge wire?
If you plan to do it yourself fairly inexpensive.Depending on the type of panel you have breakers start as low as $3.00 for a 15amp breaker. If you are looking to have a professional do it you will probably pay at least $5.00 per breaker plus whatever the going rate for labor in your area is.
Can a 100 amp main have 2 50 amp breakers?
Yes.Additional InformationBreakers and fuses protect the wires to prevent fire. The 100 Amp breaker in the meter base (main) protects the wire from the meter base to the breaker panel. The 50 Amp breaker in the breaker panel protects the wire from the breaker panel to the outlet. Sometimes the 100 amp main breaker is located in the panel.If you are asking "Can you use two 50 amp breakers for the main breakers with a 100 amp service, then yes you can. The National Electrical Code allows you to use up to 6 breakers as the main overcurrent protection.
What is an electric shared neutral?
An electric shared neutral is the white or negative wire that is shared between two electrical circuits on a basic single phase system. Most electrical devices use 120 volts and require a "hot" wire and a neutral wire to operate. Some larger devices use 240 volts and require two "hot" wires to operate. Two circuit breakers in an electrical panel can share one neutral wire as long as the breakers are not on the same "leg" of power. When looking at an electrical panel there are usually two "legs" of power feeding all the breakers, each leg has 120 Volts to ground, if the "legs" are combined you will have 240 Volts. A neutral wire can be shared by two circuits as long as the breakers are on separate "legs". If someone needed to add two circuits in their home, the could run what is called a 3-wire romex, It has a black wire, a red wire, a white wire and a ground wire. The white wire is the neutral for both the black and red 120 volt circuits, and the breakers for the new circuits would need to be on separate "legs" in the panel.
What is a branching circuit?
Each of the circuit breakers in the service panel controls electricity on a branch circuit. A branch circuit is typically a loop of wire that runs from the service panel, out to receptacles, light fixtures, appliances, etc. and back again.
What gauge wire to use for direct burial for a garage that is 400 feet from your house?
Depends on the size of the sub-panel in that garage. If you are installing a 60 amp sub-panel 400 feet away from the main service panel then use AWG # 4.
What size wire is needed to feed a 125 amp sub panel from a 200 amp panel less than 200 wire feet away?
A #1 copper wire with an insulation rating of 90 degrees C is rated at 140 amps.
How many amps can a 8 gauge wire run coming from the ditribution panel to the sub panel 25 feet away?
A #8 copper wire with an insulation factor of 75 or 90 degrees C is rated at 45 amps.
Is a 12 gauge wire on 20 amp breaker safe for a sub panel?
Yes, if you are running it no farther than 100 feet. If you are going over 100 feet use AWG # 10 wire on the 20 amp breaker.
How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?
Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.
What type of welding wire is used when welding panel steel?
For steel, flux core or hard wire with Argon/CO2 is used with the GMAW process.
Will a 100 amp breaker box work if there are 5 220 amp breakers and 7 110 breakers?
It will if the 100 amp distribution board is a 20 circuit board. Ten spaces for the 240 volt breakers and seven spaces for the 120 volt breakers. There are two types of 100 amp breaker boards, one rated at 100 percent and the other at 80 percent. Depending on what rating on the panel board you are using will govern the maximum amount of current that can be legally drawn from the board. This breaker board rating will also govern the size of the main breaker installed and the wire size to feed the board, either 100 amp wire or 80 amp wire. The second consideration is what are the connected loads to the breakers, with the total of seventeen breakers, the board can only supply as much amperage as the main breaker will allow.
