0
What wattage of voltage converter should be used to power a product that is 3400 watts and uses a power input of 110 volts?
Wiki User
∙ 8y ago
Anything over 3400 watts is ok for a converter to power the product. The converter's rating is a maximum value so it can power anything up to 3400 watts.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is the incoming voltage from the current source to the transformer called?
the incoming voltage from the current source to the transformer is called primary voltage.....
In the unknown of measuring the voltage what should be the setting of VOM selector?
Use the highest available voltage setting. One should know the system voltage before attempting to measure, other wise it may lead to accidents.
Where to buy a voltage converter?
Three phase electricity is generally used when you have a high power device, such as a motor, that benefits from the three phase design. Since this involves high power, there will be no "portable and small" device to convert from single phase to three phase. Certainly, you could have a small electronic inverter, or a motor generator set, but to make sense, you are not talking "portable and small".
Technician A says that the current draw should decrease as the voltage decreasestechnician B says that the current should increase as the voltage decreases Which technician is right?
Both technicians are right, and both technicians are wrong, because not enough information is present in the question, nor in their statements. Given constant impedance, current should decrease as voltage decreases, while given constant power, current should increase as voltage decreases.
How can you change high volts to 9 volts?
A voltage divider (two resistors in series) will achieve the required result. The value of the resistors will depend on what current is required to be supplied. It also matters what variation from 3V is allowed since taking current will make the voltage drop. An electronics parts shop will sell components to make a more efficient system. Or you could get 3 voltage regulators .. 9V then 5V then 3V in series .. that should keep the voltage stable as long as the 9V supply is
How To Use A Voltage Converter For Your Imported Electronics?
A lot of people have lost their precious electronics because they did not suspect that they needed to use a voltage converter transformer or they simply did not know how to use one. If you bought your electronics in Europe or Asia and then brought them home to the USA then chances are the specifications will require that you use a voltage converter with them. Otherwise you will blow up your electronic product or it will simply not come on at all. There is no reason to be intimidated when it comes to using a voltage converter transformer, it is actually easier than it looks or sounds. The following steps below will show you how to easily use a voltage converter on electronics operating on 220v. 1. Your first step should be to take a look behind the voltage converter transformer. Here you are supposed to find the input voltage selection panel. It is usually red in color on most models of voltage converters. The input setting will depend on your current location. If you are in the USA you will have to set the input voltage to 110v. If you are in Europe however it will have to be set to an input of 220v. 2. Turn the converter around and take a look at the front. At the front of the input converter you will find a universal socket. It is called a universal socket because it means that it can be used for both plugs that need to be grounded and those that do not. You will not be required to get another adapter to fit in your electronics’ adapter. This universal socket is output source. This is where you will have to plug in your 220v electronic product. 3. After you have plugged in the 220v product, you then need to switch on the voltage converter transformer and then your product. You should never switch on the electronic product and then the voltage converter. There may be a bit of current still left in the converter which compounded with the new settings you just chose could permanently damage your product.
How to Protect Appliances Using Voltage Converter?
One of the best investments a traveller can make when visiting countries around the world is to pack a voltage converter into his suitcase. An American traveller who is visiting for business or pleasure to European countries, Asia or the African continent, along with numerous other foreign ports, typically wants the convenience of using his own personal care appliances on the road and the traveller will throw a hair dryer, electric curling iron or electric shaver into the luggage. But unless the traveller uses a voltage converter at his travel destination, there is the risk of permanently damaging personal electronic appliances which are designed to operate at a lower voltage frequency than that supplied by electrical outlets in foreign countries. A voltage converter, also called a transformer, protects the appliances that normally are used at 110 volts from any adverse effects when plugged into electrical outlets performing at 220 volts or more. The converter steps down the energy level from high to low when the unit is plugged in aided by the voltage converter. Simply plugging in an electronic device directly into an outlet built for high voltage is asking for trouble. Not all voltage converters are adequate for all electronic devices. Check to make sure that the voltage converter you plan on using has sufficient wattage to power the electronic device you want to use. Look on the label located somewhere on your electronic appliance to find out what wattage or amperage the device uses to properly operate. Then choose a voltage converter designed to handle a wattage level even higher than that listed on your appliance. If you cannot locate the wattage on the device but do know the amperage, there’s a simple formula for calculating the wattage: Multiply the amperage by 110 volts or 220 volts to arrive at the minimum wattage required to power the unit. If the country the traveller is visiting has an unstable current, it’s important that the voltage converter used also doubles as a voltage regulator or voltage stabilizer in order to stabilize fluctuating currents. Any traveller who is in doubt about plugging in a computer, hair dryer, curling iron or other electronic device brought from home should check with the hotel or bed and breakfast management to ask about the type of voltage converter necessary to safely use their equipment during their stay without risk of equipment damage or fire.
What must you match when purchasing a power supply?
The equipments power requirements, and the mains voltage. The output of the power supply must be able to deliver the correct voltage to the equipment, at the appropriate wattage. Additionally, it should be capable of operating on the supplied mains voltage and wattage.
How many amps do you need if you have a 480 volt space heater?
The heater should have a wattage rating (very few list amps). Calculate the amps using the wattage and voltage. Amps = Watts/Volts(480).
Power is a measure of?
It is a measure of electrical power. It is Voltage multiplied by Amps. All electrical applicances should give it's wattage or at least it's voltage and Amps so you can work out the wattage. It should be noted that that figure is the maximum that appliance would use.
110 volt motor 14amp pull how big of a 12 volt converter do you need to run this?
converters are usually listed in Watts output- sometimes with a surge wattage about 2 times the normal running wattage- motors usually have a surge need to start and then even out- so assuming this motor runs at 14amp= Watts = volts X amps, you should need 1540 watt converter- 2000 watt converter to be safe
What voltage of laser is needed to injure a person?
It Isn't about voltage, it is about wattage. The amount ow watts the laser is. 10mw can blind someone and 10w can burn through skin. Anything over this is very dangerous and should on be used by professionals
What kind of speaker wire should you use?
Speaker wire should be sized to the maximum wattage that the speakers can handle. Use the following formula Amps = Watts divided by Voltage of the system driving the speakers.
How do you tell the voltage of landscape lights?
take the power it needs and the current it pushes, and divide.V=P/IAnswerLook at the nameplate of the voltage converter -it will specify the output voltage to the lamps. Alternatively, look at one of the lamps, it should have its rated voltage printed on it together with its rated power.
What Wattage should the UVB fixture be for a beardie?
The wattage of the UVB fixture for a beardie should be 26 watt bulb.
Can anyone tell the power ratings of different appliances?
attach at the back portion of the applianceAnswerAll appliances must have a label attached to them, indicating their rated voltage and rated power. For example, this information will be printed on the globe of an incandescent lamp, or somewhere inside the door of a fridge, or moulded onto the plastic body of an electric drill, etc.
Which kind of inverter is needed to run a table fan?
The voltage and frequency should be marked on the fan. This should match the voltage and frequency of the power coming out of the inverter. The inverter also has be capable of supplying anough power (in watts).
