magnetic flux will be induced its use to rotate the shaft or given some force
The equation of an inductor is ...di/dt = V/L... meaning that the rate of change of current in amperes per second is proportional to voltage and inversely proportional to inductance in henries.If, for example, you connect a 200 millihenry inductor across a 12 volt battery, the current will increase at a rate of 60 amperes per second.Now, the question is, can the inductor, conductors, and/or battery handle that? The answer is no. Something is going to fail. The inductor will rather quickly look like a short circuit across the battery.This example does not take resistance into account. Practical inductors, conductors, and batteries have resistance, and that will place an upper limit on current but, still, this is not an appropriate way to connect an inductor to a battery.DO NOT TRY IT IN THE LAB - THERE IS RISK OF EXPLOSION.
Its a point on the galvanometer where the galvanometer shows no deflection as no current passes through it.
It means that the current passes through 0 50 times a second.
If two circuit elements (e.g., two resistors) are in series (a series circuit), the current has to pass first through one, then through the other. If they are in parallel, the current has a choice, through which of the elements it passes.
If an electrical current passes through a conductor, there is an induced voltage (because no conductor has perfectly zero ohms), resulting in power dissipation, and there is a magnetic field, which can interact with other conductors in the vicinity of the first.
A:The inductor does not allow ac signal to pass through. It blocks ac and passes dc. If the switch is open, then the ac signal wont pass. If the switch is closed, then the ac signal will pass through the switch.AnswerIt is incorrect to say that an inductor 'does not allow' the passage of an alternating current. An a.c. current will pass through an inductor, although the inductor will limit the value of that current due to the inductor's inductive reactance. Inductive reactance, which is expressed in ohms, is directly-proportional to the inductance of the inductor and to the frequency of the supply. The value of the current is determined by dividing the supply voltage by the inductive reactance of the inductor.If the switch is connected in parallel with the inductor, then closing the switch will apply a direct short circuit across the inductor, and the resulting short-circuit current will cause the circuit's protective device (fuse or circuit breaker) to operate.
It will get hot.
it resists the flow of cuurent
when electric current is passed through acidified water hydrogen gas is released at the cathode..
Basically, if you fill a room with steam and pass an electrical current through it... Does anything interesting happen?
When current passes through an electric bell, the armature gets magnetised and attracts the gong hence ringing the bell.
There is a piece of filament in every light bulb, which has so much friction that when the electric current passes through it, heat energy is produced. This heat energy is then converted to light energy.
Both a resistor and an inductor are electrical components designed to impede the unregulated flow of electricity. Where they differ is that inductors store energy in their induction coils which forms a magnetic field that focuses energy by the principle of inductance. As electricity passes into the inductor, current will slowly rise to a specified level. A resistor simply impedes the flow of electricity according to its property, but does not store energy. It also does not control the rate at which the current changes, it just changes the current allowed to pass through.
Because the voltage induced is proportional to the rate of change of current, and the maximum rate of change of current occurs at the point where the current waveform is 'steepest' -i.e. as it passes through zero. So, as the current passes through zero, the corresponding value of induced voltage is maximum, which means the voltage and current waveforms are displaced by a quarter of the wavelength, or 90 degrees.
A VAR Meter is used to measure Reactive Power in AC Circuits - Pure reactive components dissipate zero power, which makes sense in a DC circuit, as a capacitor passes no DC current and an inductor displaces no voltage. Yet, in an AC circuit, the reactive components "seem" to dissipate power, as current passes through the capacitor and the inductor sees a voltage drop. This counterfeit power is called "reactive power" and is measured not in Watts, but in VARs (Volt-Amps-Reactive). Its mathematical formula symbol is "Q". A VAR Meter is used to measure Reactive Power in AC Circuits - Pure reactive components dissipate zero power, which makes sense in a DC circuit, as a capacitor passes no DC current and an inductor displaces no voltage. Yet, in an AC circuit, the reactive components "seem" to dissipate power, as current passes through the capacitor and the inductor sees a voltage drop. This counterfeit power is called "reactive power" and is measured not in Watts, but in VARs (Volt-Amps-Reactive). Its mathematical formula symbol is "Q".
because of flux produced in coil of inducterAnswerThe potential difference (not 'potential') induced into a pure inductive component is proportional to the rate of change of current. The greatest rate of change of current occurs when the current waveform passes through zero (i.e. is at its steepest angle). So the voltage is maximum when the current is passing through zero -which means that the current is lagging the voltage by 90 degrees.
No current passes through the Atacama Desert but the Humbolt, or Peruvian Current, passes just off shore and has a great influence on the climate of the Atacama.