0
What would happen if a hydraulic system had a leak and lost some of its fluid?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What can you infer about why hydraulic fluid is usually made of oil instead of water?
Because its from arabia!! :D water would rust the system.
Is hydraulic fluid flammable?
The most commonly used hydraulic fluids are oils, so yes they are flammable. However, most any fluid COULD be used as a hydraulic fluid depending on the system design requirements. So it really depends on exactly what type of fluid is being used whether it is flammable or not. Water is a "hydraulic fluid" and is not flammable. Under NFPA standards, petroleum-based hydraulic fluids are not "flammable" if their flash point is above 100o F (37.8o C); they would be "combustible". NFPA 1 (2009): 3.3.153.2 Definition of Flammable Liquid
Why do hydraulic systems use liquids?
Fluids are incompressible, relatively speaking, hence the pressure applied through the system is directly transmitted to the object which you want to lift. If you used a gas, you would waste a lot of energy compression the gas-hence the system would be inefficient. There's another reason. Hydraulic systems using gases instead of liquids can be very efficient indeed--witness the brakes on a big truck. They are ALL specifically, air--powered, and they work very well. The compressor in a gas system doesn't enter into efficiency calculations because in a liquid system, with the exception of something like car brakes, there's a pump. And in some cases you can't use a liquid hydraulic system. On a big printing press, there are a lot of compressed roller lifters because no one wants a book that has hydraulic fluid spattered on the pages, and if your press springs a leak in the roller lifters that is what will happen. The biggest advantage a liquid hydraulic system has is the nearly complete lack of lag. In a fluid power (the industrial term for a hydraulic system using liquid fluids) system, the whole system is charged with fluid. When you press against the fluid at one end, or pump some more in depending on what the system is, the force is instantaneously transferred to the thing you are attempting to move. OTOH, in an air system you've got to fill the lines with air before anything moves. (This is another reason why you shouldn't cut off semis on the interstate-at 55mph the truck has no brakes for 32 feet after the driver steps on the pedal.)
What causes the pressure in liquids and hydraulic machines?
Fluids are incompressible, relatively speaking, hence the pressure applied through the system is directly transmitted to the object which you want to lift. If you used a gas, you would waste a lot of energy compression the gas-hence the system would be inefficient.AnswerThere's another reason. Hydraulic systems using gases instead of liquids can be very efficient indeed--witness the brakes on a big truck. They are ALL gas--specifically, air--powered, and they work very well. The compressor in a gas system doesn't enter into efficiency calculations because in a liquid system, with the exception of something like car brakes, there's a pump. And in some cases you can't use a liquid hydraulic system. On a big printing press, there are a lot of compressed-air roller lifters because no one wants a book that has hydraulic fluid spattered on the pages, and if your press springs a leak in the roller lifters that is what will happen. The biggest advantage a liquid hydraulic system has is the nearly complete lack of lag. In a fluid power (the industrial term for a hydraulic system using liquid fluids) system, the whole system is charged with fluid. When you press against the fluid at one end, or pump some more in depending on what the system is, the force is instantaneously transferred to the thing you are attempting to move. OTOH, in an air system you've got to fill the lines with air before anything moves. (This is another reason why you shouldn't cut off semis on the interstate--at 55mph the truck has no brakes for 32 feet after the driver steps on the pedal.)
What do you need to make a hydraulic arm and how do you make one?
First off, working with hydraulics can be extremely dangerous. With pressures up to 2500 PSI or more, if something is connected incorrectly serious injury or death could occur. Hydraulic systems should only be serviced and/or created by persons with the correct training and experience. Before you can start any building, you will have to decide exactly what you want your hydraulic arm to do. How many limbs will it have? How much weight will it move? A background in basic statics is desirable as you will need to calculate the optimum point on the arm to connect the hydraulic cylinders to to obtain the maximum amount of force from the lever. The basic components that make up a hydraulic system are as follows: -Hydraulic pump (powered by a rotating engine or motor of come kind) -Hydraulic cylinders (this is where your power and motion actually come from) -Hydraulic valves (connected to levers or solenoids to control the flow of hydraulic fluid) -Hydraulic fluid (automatic transmission fluid is very similar and would also work) -Hydraulic fluid reservoir tank (to store fluid that is not currently being used in expanded cylinders) -Hydraulic hoses and fittings to connect everything together And of course the steel or other material for the limbs of the arm itself. Other objects like a pressure gauge or safety valve would be good ideas as well. When selecting these components you need to make sure that -your motor or engine has enough power to run your hydraulic pump -your hydraulic pump has enough power to run your cylinders -your cylinders can produce enough force to accomplish what you need them to accomplish -and that your hoses and valves can handle the amount of pressure your system will be under
Will low hydraulic oil in trans for a Chevy s-10 2.2 cause clutch not to engage?
There is no hydraulic fluid in the transmission. However, there is hydraulic fluid in the clutch system. If the clutch fluid reservoir is empty it would cause clutch not to operate.
What does transmission fluid do?
Transmissions are hydraulic just like your brake system or power steering system. Without transmission fluid you would have no hydraulic pressure for it to operate nor would you have lubrication. Trans fluid also has cleaners in it to clean your transmission as clutches, and gears wearaccumulate inside.
Can you use brake fluid in hydraulic cylinders?
Brake fluid is a type of hydraulic fluid with very specific properties. You would have to check the compatibility of the particular fluid with the components in your system. This would include the cylinders, seals, hoses, and any other internal components exposed to the fluid. The best thing is to use the exact fluid that the system manufacture specifies.
Does the slave cylinder open and close?
No, the slave cylinder is a typical hydraulic piston; if the system was 'opened' then the fluid would come out.
What can you infer about why hydraulic fluid is usually made of oil instead of water?
Because its from arabia!! :D water would rust the system.
What kind of power steering fluid would you use in a vauxhall astra?
For the TS Astra with hydraulic-electric power steering, it takes a Pentosin CHF fluid. A couple of equivalents I have come across include Castrol Hydraulic System Mineral Oil Plus, and Penrite LDAS fluid.
What type of brake fluid does the pneumatic ABS system use?
Pneumatic = Air! There are brake systems that use a combination of both pneumatic and hydraulic components. In those combination braking systems you would use the hydraulic brake fluid that the manufacture specifies.
Is hydraulic fluid flammable?
The most commonly used hydraulic fluids are oils, so yes they are flammable. However, most any fluid COULD be used as a hydraulic fluid depending on the system design requirements. So it really depends on exactly what type of fluid is being used whether it is flammable or not. Water is a "hydraulic fluid" and is not flammable. Under NFPA standards, petroleum-based hydraulic fluids are not "flammable" if their flash point is above 100o F (37.8o C); they would be "combustible". NFPA 1 (2009): 3.3.153.2 Definition of Flammable Liquid
Does a log splitter use hydraulic fluid or hydraulic oil?
Both! The gas engine would take oil then the log splitter that runs the hydraulics would take a specific hydraulic fluid. Its best to go by what the manufacture says
Why you use hydraulic jack oil only?
designed for hydraulic jack perhaps power steering fluid would work Brake fluid Ruins pump
What would happen if windshield washer fluid was put in brake fluid reservoir?
You need to have the brake fluid changed immediately. Washer fluid will damage all of the seals in the brake system
What is a hydraulic system its uses example of its uses and dangers of a bad hydraulic system?
It's where fluid (usually oil) is used to amplify pressure. Examples would be forklifts, car jacks, lifts of all kinds and the brakes on your car. Lose pressure on some of these in use, and they will fall.
